Jenn-Air SCE30500 Verticalduct Inside Wall, Outsidewall Thefloor, Powerin, Shadedarea, Fe Et

11. Wall Vent Cutout (Figure 11)

center to center. II _- _ . WALLSTUD

•Willthevent ductbe6" (15.24cm) roundthroughthewall or3-1/4"x 10"

	(8.26 cmx 25.4 cm) rectangle,verticatlyinside the wall?	/"
•	oceeveasuserr6"uareusu03-1/4"x10."
	See DuctingInstructionsfor rear duct insidethe wall. Not : Cutout in the
	wall must clear 3-1/4" x 10" (8.26cm x 25.4 cm) transition elbow
•	L cat the lo est stud t your proposed vent h le lo ation Use the	(/_._
	followingchartto figurethe "X" dimension.Seethe illustrationfor the other
	dimensions.

VERTICALDUCT INSIDE WALL

Round(15.24cm)

. . .

(Figure 11)

c°

(8.26cmx 25.4cm)

THROUGH

THROUGH

"X" MINIMUM	4" (10.16cm)	6"(15.24cm)	OUTSIDEWALL		THEFLOOR
			12.54cm
			I"	)_
• A 1" (2.54cm) lengthof duct mustprotrudethroughthe wall for connection			_-		"=""--._"D'U'_hT
tOthe blower.			(_
locatedfrom 9-3/8"to 11" will requireunitto be raisedover blowerfor			_1_]	J'J_fT
NOTE:Optimum vent location is 11" to		17" from edge of cabinet. Vents
			_ / j f j _r _.-iJ /_,3rf		/ _ _ _ Jr f Jttf n_f IF •
installation.			METALJTAPEOUCTDI DUCTTAPEucT
12. Install Blower (Prior To Installing Range) (Figure 12)				(Figure 12)

•Refertoyourvent plan. it may be desirableto attachpart of the ducting

•	to theblowerbeforeit is installed.		L'IOCATEELECTRICA'L
	Positiontheblower(seeillustration)and attachitto the floorwithat least		POWERIN
	two (2)screws:		SHADEDAREA I
•	Applyducttape aroundblowerexhaust/ducjtoint.		I
,3. Install Electrical (Figure 13)
• Note: Observe all localelectricalcodes.
•	CAUTION:Make sure powerto cable is OFF.	_
•	Locatetheelectricpowersupplyinthefloor orwall, anyplace inthe shaded	/.-_,	5 FEETOF
	areawhichwill clearthe blower.	_)	ELECTRICAL CABLE
• DirectConnect.Pullthrough5' (152.4 cm)of electricalcable.
•	Range Cord:Canadianunitsare equippedwitha range cord. Install a		(Figure 13)
	correspondingreceptacle.
	for properwiresize.)If four conductorwire is used,see #15 for connection	/ _	cup
	to range,		w_s,eR

•See frontcoverof theseinstructionsfor propersupplyconnection.

•CAUTION:Make sure powerto cable is OFF.

14.ConnectElectrical (Three ConductorWire)(Figure 14)

•Removethr the rangeconductorcopperstandardpoelect ical service cover, located on the back, lower

Us ee orfourwercable (seefront cover

left-handcorner.

•Installa 3/4" (1.91cm) clampin theholeprovidedbelowtheterminalblock.

•Strip 3" (7.62cm) of outer insulationfrom the cable.

•Strip 1/2" (1.27cm) of insulationfrom each wire,

•Pull the cable through the cable clamp. Attach the BLACK, RED, and WHITE wires (see illustration.) Tighten the terminal block nuts and the cableclamp and install cover.

•On ranges equippedwith a range cord, plugthe cord into its receptacle.

•Skipto Step #16.

__o t "-NEU'mAL(WHITE)

__,_w____

,_CABLECLAMP _

(Figure 14)