Braun MR740cc manual Safety features, Using your handblender, Using your chopper attachment

Page 10

Switch release

Charging or operation

button (2) pressed

conditions

down

 

 

 

Green

Battery is fully charged

 

 

Red/green flashing

Charge sufficient for at

 

least one usage

 

 

Red

Battery is discharged

 

 

Red

Overheating protection

 

active (go to Safety

 

features Α Overheat

 

protection)

 

 

Safety features

Switching on the appliance / Switch lock

The appliance has a switch lock. To safely switch it on, follow these points:

1First press the switch release button (2) with your thumb and hold.

2Then press the On switch (3). During operation, you can stop pressing the switch release button.

If the On switch (3) is not pressed within

5 seconds, the appliance cannot be switched on. The pilot light goes off.

In order to switch the appliance on, start again with step 1.

Overheat protection

When the overheat protection feature is active, the appliance turns off and the pilot light shines permanently red.

Reason

Trouble shooting

 

 

Blade is blocked

1. Remove motor part

 

2. Remove the food/

 

blockage

 

3. Place the motor part

 

into the charging unit

 

(connected to the mains)

 

for at least 1 second

 

4. Processing can be

 

continued

 

 

Appliance is

Follow points 1.-4.

overheated

If the pilot light still shines

 

red when switching on the

 

appliance, place the motor

 

part back into the charging

 

unit and let it cool down

 

for ca. 1 hour. During this

 

time, the pilot light flashes

 

green.

 

 

Auto Off

For safety reasons the appliance turns off after

4 minutes of permanent usage. The appliance can be turned directly on again.

Using your handblender

The handblender is perfectly suited for preparing dips, sauces, soups, mayonnaise and baby food as well as for mixing drinks and milkshakes.

a)Remove knife protection at the bottom of the blender shaft by removing the adhesive tape. Insert the motor part (4) into the blender shaft (6) until it locks.

b)Introduce the handblender vertically into the vessel, keep the switch release (2) pressed down, then press the On switch (3).

c)To remove the blender shaft from the motor part, press push buttons (5).

When operating the handblender in hot liquids do not immerse the blender shaft into – or remove it from the liquid while the appliance is switched on.

Recipe example: Mayonnaise200–250 ml oil,

1 egg (yolk and white),

1 tbsp. lemon juice or vinegar, salt and pepper to taste

Put all ingredients into the beaker according to the a.m. order. Introduce the handblender to the base of the beaker. After switching on, keep the handblender in this position until the oil emulsifies. Then, without switching off, slowly move it up and down until the mayonnaise is well combined.

Using your chopper attachment

The chopper is perfectly suited for chopping meat, cheese, onions, herbs, garlic, carrots, walnuts, almonds, prunes etc.

N.B.: Do not chop extremely hard food, such as nutmeg, coffee beans and grains.

Before chopping ...

pre-cut meat, cheese, onions, garlic, carrots, chilis (see processing guide S. 5)

remove stalks from herbs, un-shell nuts

remove bones, tendons and gristle from meet.

10

Image 10
Contents Cordless Hand Processor MultiquickMR 740 cc Page b c d 400 g 150 g + 700 mlPage Page Page Page Page Pilot Light DescriptionCharging EnglishUsing your chopper attachment Safety featuresUsing your handblender Blade is blockedCrushed ice CleaningChopping Shakes, drinks, purées99676583/VIII-10 China/GB