Grundig WORLD RECEIVER HOW to GO to a Specific Shortwave Frequency, Alarm Feature did not Work

O P E R A T I O N G U I D E

The traditional 31 meter band is considered a night band, covering the frequency range 9.5-9.9 MHz. In practice, broadcasts may be found starting at 9.2 MHz and extending all the way up to, but not including 10 MHz.

Step 1. Turn on the radio.

Step 2. Tune to the frequency at the beginning of the band, in this case, 9.5 MHz.

Step 3. Now tune manually, using quick, short over-and-over presses on the + tuning button. Each press advances the frequency by 5 KHz. Shortwave broadcast stations are spaced in these 5 KHz steps. Now, tune through the band, listening to any stations that you find interesting. You can move around in the band, going up or down frequency, by pressing the + or - tuning buttons.

Step 4. Alternatively, use the AUTO SCAN feature. The tuner will automati- cally stop when it encounters a station strong enough to stop the scanner. Weaker stations may be missed when using this method in shortwave. If you are looking for stations that may be weak, use the manual tuning method outlined in step 3 above.

HOW TO GO TO A SPECIFIC SHORTWAVE FREQUENCY

Press-and-hold the + or - button until the tuner gets into the general frequency range of where the specific desired frequency is located. Then, release-press- release the button to stop the scan. Then, use individual, quick, short presses of the + or - buttons to get to the exact frequency that you are selecting.

LEARNING MORE ABOUT INTERNATIONAL SHORTWAVE BROADCASTS Refer to the GRUNDIG SHORTWAVE LISTENING GUIDE that came with your radio, contact us by phone or

visit our web site.

T R O U B L E S H O O T I N G

Contact Grundig if none of the suggestions below restore normal operation.

SHUTS OFF ABRUPTLY WHILE PLAYING

Dead batteries. Replace them with new, fresh AA alkaline batteries.

WILL NOT TURN ON AND LCD IS ACTIVE

Dead batteries - as above.

WILL NOT TURN ON AND LCD IS BLANK

Probably dead batteries. If not, a 'reset' may be needed. To perform a 'reset', remove the batteries or unplug AC adaptor for about one minute. Then, reapply power. The display should become active and the radio should turn on.

WILL NOT TURN ON USING THE 'POWER/STANDBY' BUTTON

The clock must be set to turn the radio on/off with this method. - : - - must not appear in the clock display.

CLOCK DISPLAY READS - : - - AND MEMORIES ARE LOST

The radio was turned on when batteries were replaced or when an AC adaptor was plugged in or out.

THE ALARM FEATURE DID NOT WORK

After setting the ALARM-ON time, 'STANDBY' was not activated to appear in the LCD. See the instructions for SETTING THE ALARM-ON TIME.

T E C H N I C A L I N F O R M A T I O N

FREQUENCY RANGE: FM 87.5-108 MHz; MW (AM) 530-1710 KHz; SW 2-30 MHz.

TUNING CONTROLS: Up/Down tuning buttons. Autoscan and manual tuning. 30 Memories with memory scan, 10 each, AM, FM, SW.

ADDITIONAL FEATURES: Dual conversion superheterodyne AM and SW cir- cuitry. Liquid Crystal Display - 2.2 x 3.5 cm. Clock. Alarm - wake to radio. Sleep Timer.

SPEAKER: 57 mm (2-1/4 inch); 16 ohm; .25 watt.

EARPHONE SOCKET: 3.5 MM (1/8 inch)

POWER SUPPLY: Two AA batteries. 3 VDC AC adaptor (not supplied).

AC ADAPTOR SPECIFICATIONS: (adaptor is not included with purchase) Output, 3 VDC, negative polarity, 250 milliamperes or greater; Plug tip diameter dimensions, 3.4 mm outer, 1.3 mm inner.

ANTENNA: Telescopic for FM, SW. Ferrite Bar (internal) for AM.

DIMENSIONS: 11.5 x 6.5 x 2.4 cm. 4 1/2 x 2 9/16 x 7/8 inch.

WEIGHT: 165 g.

CABINET COLOR: Titanium Silver

12 13