Critical Parts Servicing, Microwave Defrost

(To those 700W microwave oven) to make the oven operating in normal. When the bell of the timer rings, open the oven door, the water should have boiled. If it have not been boiled yet, but is very hot, check whether the voltage is less than 120V. If the voltage below 120V but the water can be boiled after a little more time beating, it is normal.

5.4.4MICROWAVE DEFROST:

Place a graduate of about 200ml water on the turntable glass tray of the oven, power set middle, time set 4 minutes to make the oven operating in normal. When the bell of the time ring, open the door. It would be normal if the water is lukewarm.

6.CRITICAL PARTS SERVICING

6.1IMPORTANT THINGS TO DO PRIOR TO CRITICAL PARTS SERVICING:

The following instructions are CRITICAL to the owner’s safety. Be sure to follow all the instructions. Contact the manufacturer or distributor if you have any question.

1.If the oven is operative prior to servicing, a Microwave Leakage Test (a. k. a. Microwave Emission Check) should be performed prior to servicing the oven Refer to Section 7.3, Microwave Leakage Test. For the detailed check procedures.

2.In the event that any microwave oven found to have microwave emission level in excess of 4 mW/cm2. The following procedures should be followed:

(1). .Inform the distributor; importer, or manufacturer the finding. Record it in the logbook as well.

(2). .Repair the unit at no cost to the owner.

(3). .Investigate the oven and ascertain the cause of the excessive leakage.

(4). .Hold the oven in your facility and instruct the owner not to use the unil until the oven has.

3.In the event that the oven operates with the door open. The following procedures should be followed:

(1). Tell the user not to operate the oven.

(2). Hold the oven in your facility until it is investigated and repaired.

(3). Contact the manufacturer and CDRH (FDA) immediately.

6.2INTERLOCK ASSEMBLY REPLACEMENT AND ADJUSTMENT.

1.If you suspect defective primary, secondary or monitor interlock switches, use your ommeter (digital or analog type) to check the electrical continuity.

2.Make sure the power cord is pulled out and the high-voltage capacitor is discharged before the electrical continuity check.

3.Set the ohmmeter to “Low Resistance” range and connect both leads (alligator clips) to the switch terminals.

4.Open the door and notice the meter reading the primary or secondary interlock switch should show an “infinite” resistancc when the door is open. Replace it when it is defective. The monitor interlock should show a “zero or near zero” resistance when the door is open. When the door is closed, the readings will be opposite.

5.If the oven has been rendered inoperative due to the failure of the monitored safety (primary and /or secondary ) interlock(s). You should replace all of the monitored safety interlock switched and the monitor switch.

6.Refer to Chapter 4, Sections I and X for how to remove and assemble the interlock and monitor switches.

7.Always refer to Section 0.4 for adequate wiring diagram. Monitor interlock must always be installed. Repeat Step 6.2.4 to check electrical continuity.

8.Perform required checks and tests as described in Chapter 7 before releasing the oven to the owner.

SM-GA0005 specifications

The Sanyo SM-GA0005 stands out as an innovative device that blends functionality and design, catering to the needs of modern users. This device has garnered attention for its robust set of features, cutting-edge technologies, and practical characteristics that enhance user experience.

One of the most prominent features of the Sanyo SM-GA0005 is its sleek design, which combines aesthetics with ergonomic functionality. Its lightweight body makes it easy to carry, and the minimalist approach to its interface allows for intuitive navigation. The display is vibrant, offering sharp visuals that enhance multimedia experiences, from watching videos to viewing photographs.

In terms of performance, the SM-GA0005 is powered by a high-efficiency processor, which ensures smooth multitasking and lag-free operation. Whether users are browsing the internet, streaming content, or using demanding applications, this device holds up under pressure. The internal storage options are ample, allowing users to save a significant amount of data, from documents to media files, without the need for external storage solutions.

Connectivity is another essential aspect of the Sanyo SM-GA0005. It supports various connectivity options, including Wi-Fi and Bluetooth, ensuring users can stay connected regardless of their circumstances. The inclusion of advanced wireless technology allows for swift data transfer and a stable internet connection, essential for both personal and professional use.

Battery life is a crucial characteristic of any modern device, and the SM-GA0005 excels in this regard. With an energy-efficient battery, users can expect prolonged usage without the hassle of frequent recharging. This is particularly beneficial for those who are always on the go, as it ensures the device remains operational throughout the day.

In addition, the Sanyo SM-GA0005 boasts a comprehensive set of security features, including biometric authentication and encryption options, providing users with peace of mind when it comes to data protection. This emphasis on security reflects the growing concern over digital privacy and the need for safe, reliable devices.

Overall, the Sanyo SM-GA0005 represents an impressive combination of style and substance, making it an appealing choice for consumers seeking an efficient, reliable smartphone. Its blend of performance, connectivity, battery life, and security features solidifies its place in the competitive market, catering to diverse user needs and preferences.