Ericsson LBI-39101A manual Software Installation SET-UP Procedure, PC Cmos SET-UP Program

Page 26

LBI-39101 SOFTWARE INSTALLATION AND SET-UP PROCEDURE

SOFTWARE INSTALLATION AND

SET-UP PROCEDURE

NOTE

Unless otherwise noted, all procedures in this manual should be performed in the order presented.

PC CMOS SET-UP PROGRAM

C3 Maestro software is factory-installed on the PC's hard disk drive and the software is configured properly for standard installations. Therefore, during a typical console configuration, the information in this section may be bypassed.

All PCs used with the C3 Maestro store start-up configurations in CMOS memory. This information is read by the computer's BIOS and it may be changed by executing a set-up program during the PC's boot process. Execute the PC's set-up program only if a built-in (main board) COM port must be disabled/enabled or if documentation included with the PC deems it necessary for some other reason.

NOTE

Time and date will be correctly set by the CEC/IMC Manager (MOM PC) when the console is on-line with the CEC/IMC.

∙COM1 is disabled by setting "Serial Port A" to "Off". This disables the computer's main board COM1 serial port so the plug-in RS-422 board used for CEC/IMC control data interfacing can be set to COM1 without conflicting. This is the standard factory configuration. If the plug-in RS-422 board is not being used and the main board COM1 port is used for CEC/IMC control data interfacing, set "Serial Port A" to "Serial 3F8h IRQ4".

If any necessary changes are made to the COM1 or COM2 settings, verify they are saved before rebooting/resetting the computer. Typically, a save is accomplished by pressing the <F3> function key.

Other PCs

Refer to the documentation included with the PC for COM port configuration details. If using the plug-in RS-422 board as COM1, verify the PC's main board COM1 port is disabled. Also verify COM2 is enabled.

FILE DIRECTORIES AND CONTENTS

Table 10 specifies PC file directories and files directly applicable to the C3 Maestro console. The MS-DOS file directory and its files are not shown. Also, other utility files not listed in the table may exist in a utility directory which are not essential to the operation of the C3 Maestro application program.

Table 10 – C3 Maestro PC File Directories And Files

Hewlett-Packard PCs

Typically, the HP set-up program is started by pressing the <F2> function key when prompted with "Setup=F2" during the boot process. Verify/configure "Serial Port A" (COM1) and "Serial Port B" (COM2) as necessary:

∙COM2 is enabled by setting "Serial Port B" to "Serial 2F8h IRQ3". This is the standard factory configuration. Normally, this serial port is used to interface the PC to the Enhanced Audio Enclosure.

ROOT DIRECTORY

(C:\)

AUTOEXEC.BAT

CONFIG.SYS

COMMAND.COM*

IO.SYS*

MSDOS.SYS*

CONSOLE

DIRECTORY

(C:\CONSOLE)

AUXIO.DAT

CONFIG.DAT

CONKEY.COM

CONSOLE.EXE

EDITOR.EXE

ENGLISH.DAT

ENTITY.DAT

FONT33.DAT

SETUPS.DAT

*MS-DOS 6.0 or later. IO.SYS and MSDOS.SYS are hidden files.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Table of Contents LBI-39101AAudio Cable 100-FOOT 19B804083P2 File Directories and ContentsEditor Program TablesFigures This Page Intentionally Blank General GeneralPersonal Computers Board SET-UPBoard SET-UP Enhanced Audio EnclosureMinimum Volume Level DIP Switch SW1 Position Speaker AssemblyDigital Pots Settings Speaker Amp BoardDigital Pots Board SET-UP Maximum Volume Level DIP Switch SW1 Position FigureG3 − Speaker Amp Board SW1 Factory SettingRS-422 Board Interconnecting EquipmentInterconnecting the Equipment CEC/IMC InterconnectionsRS-422 Interfacing Co-Located Hook-Ups Control Data LinkOverview Console CEC/IMC Color Port Wire TypicalSignal Identifi PIN no Cation Connection∙ DTE Options Audio Links∙ MNP Options CEC/IMC Input or Output 2-Wire CEC/IMC Identification 4-WireConsole Input or Output 2-Wire − CEC/IMC-To-C3 Maestro Interconnections Co-Located Interconnecting the Equipment Dispatch Keyboard Personal ComputerStandard PC Keyboard DeskGMic if usedWire Color DB-9 PIN Number Footswitches if used− Boom/Gooseneck Mic Wiring Boom/Gooseneck Mic if usedRecorder Outputs if used Paging Input if usedConsole-to-CEC/IMC Audio Interconnections Relay Outputs if usedCall Director if equipped Console-to-Call Director InterconnectionsType Input USE Output Name Input USE OutputAC Power and UPS Equipment Audio Tower ReplacementAudio Tower Replacement Equipment Room GroundingDispatch Keyboard Cable Color Coding Application Software InstallationMale Cable DB-9 PIN Wire USE Number Color SpeakersRelayGOutputs POWER-UP ProcedurePagingGInputs CallGDirectorFile Directories and Contents Software Installation SET-UP ProcedureLBI-39101 Software Installation and SET-UP Procedure PC Cmos SET-UP ProgramSoftware Installation and SET-UP Procedure Editor ProgramDatabase Initialization Console User Profile ConfigurationRunning the C3 Maestro Application Program Saving Database Information System Manager Database UploadsConsole Privilege Lists CEC/IMC Auxiliary I/OSoftware Installation and Upgrades Enhanced Audio Enclosure Connector PIN-OUTSLBI-39101 Enhanced Audio Enclosure Connector PIN-OUTS CEC/IMC Audio Lines female DB-25 labeled LinesEnhanced Audio Enclosure Connector PIN-OUTS Enhanced Audio Enclosure Rear Panel ConnectorsDesk Microphone female DB-9 labeled Desk MIC Call Director female DB-9 labeled Call DIRBoom/Gooseneck Microphone female DB-9 labeled B/G MIC Operator Headset Female DB-9 labeled Oper H/SPIN Name Supervisor Headset female DB-9 labeled Super H/SSelect Speaker Dispatch Keyboard Serial Input/Output Supervisor Footswitch female DB-9 labeled Super FT. SWOptional RS-422 Input/Output female DB-9 labeled I/O Female DB-9 labeled KBDRecorder Outputs 4-position terminal block labeled Recorder Terminal Name Activation MethodTerminal Name Terminal Name USECable Assembly Diagram Control Data Cable 100-FOOT 19B804083P3Audio Cable 100-FOOT 19B804083P2 Ericsson Inc

LBI-39101A specifications

The Ericsson LBI-39101A is a robust and versatile base station designed to facilitate efficient communication networks. Known for its reliable performance, the LBI-39101A plays a crucial role in enhancing the connectivity landscape for mobile operators. This equipment supports a range of technologies, making it an ideal choice for operators aiming to deliver high-quality services in both urban and rural environments.

One of the key features of the LBI-39101A is its support for multiple frequency bands, allowing it to operate across various spectrum allocations. This flexibility enables mobile operators to effectively manage their frequency resources and optimize network performance. Additionally, the base station is designed to support both 2G and 3G technologies, making it a valuable asset for operators transitioning to newer standards while still catering to older devices in their network.

The LBI-39101A also incorporates advanced receiver and transmitter technology, which enhances its ability to handle high traffic loads and support a larger number of simultaneous users. This capability is crucial in densely populated areas where network demand is high. The base station's design also emphasizes energy efficiency, reducing both operational costs and environmental impact, which is becoming increasingly important in today's eco-conscious world.

Another notable characteristic of the LBI-39101A is its modular architecture. This design allows for easy upgrades and scalability, enabling operators to expand their network capabilities without the need for extensive infrastructure overhauls. The base station can accommodate future enhancements seamlessly, ensuring that it remains competitive as technology evolves.

Moreover, the LBI-39101A includes built-in support for advanced features such as MIMO (Multiple Input Multiple Output) technology, which improves data throughput and reliability. This is particularly significant as mobile data consumption continues to rise, placing immense pressure on existing networks. The MIMO capability allows for enhanced spectral efficiency, which is crucial for maximizing the available bandwidth.

In summary, the Ericsson LBI-39101A stands out as a powerful base station with a host of features designed for modern mobile communication. Its support for multiple technologies, energy efficiency, modular design, and advanced MIMO capabilities make it an excellent choice for operators looking to enhance their networks and provide superior connectivity for users. As the mobile landscape evolves, the LBI-39101A is poised to remain a key player in facilitating seamless communication.
Top Page Image Contents