Bunn U3A service manual Digital Timer Terminals

Page 34

SERVICE (cont.)

DIGITAL TIMER (Late Models)

NOTE: All volume settings must be done with the sprayhead installed.

1.Modifying brew volumes. To modify a brew vol- ume, first check that the SET/LOCK switch is in the “SET” position on the circuit board.

To increase a brew volume, place the ON/OFF switch in the “ON” position, press and hold the START switch until you see three breaks in the water stream from the swing arm. Release the switch and press it again one or more times. (Failure to release the switch within two seconds after the third break in the water stream causes the volume setting to be aborted and previous volume setting will remain in memory.) Each time the switch is pressed, two seconds are added to the brew time period. Allow the brew cycle to finish in order to verify that the desired volume has been achieved.

To decrease a brew volume, place the ON/OFF switch in the “ON” position, press and release the START switch once for every two-second interval to be removed from the total brew time period; then immediately press and hold down the START switch until you see three breaks in the water stream from the swing arm. Release the switch. (Failure to release the switch within two seconds after the third break in the water stream causes the volume setting to be aborted and previous volume setting will remain in memory). Allow the brew cycle to finish in order to verify that the desired volume has been achieved.

2.Setting brew volumes. To set a brew volume, first check that the SET/LOCK switch is in the “SET” position on the circuit board. Place the ON/OFF switch in the “ON” position, press and hold the START switch until you see three breaks in the water stream from the swing arm and then release the switch. (Failure to release the switch within two seconds after the third break in the water stream causes the volume setting to be aborted and previous volume setting will remain in memory.)

View the level of the liquid being dispensed. When the desired level is reached, turn the ON/OFF switch to “OFF”.

NOTE: The brewer remembers this volume and will continue to brew batches of this size until the volume setting procedure is repeated.

NOTE: When brewing coffee, volume will decrease due to absorption by the coffee grounds.

NOTE: Half-Batch and full batch settings must each be set separately.

3.Setting programming disable feature. If it be- comes necessary to prevent anyone from changing brew time once programmed, you can set the SET/ LOCK switch to the “LOCK” position. This will prevent any further programming until switch is once again put into the “SET” position.

BLU/BLK wire from TL5 to P1

WHI/GRN wire from TL4 to (WHI) Pump

WHI/BLU wire from TL3 to (BLK) Pump

WHI wire from TL2 to P2

BLK wire from TL1 to P3

J2 - Three Pin connector from Half/Full Batch

Switch

P2037

FIG. 33 DIGITAL TIMER TERMINALS

Page 34

10060

080900

 

Page 33 Page 35
Image 34
Page 33 Page 35
Contents U3A Phone 217 529-6601 FAX 217BUNN-O-MATIC Commercial Product Warranty Introduction User NoticesElectrical Installation Instructions Electrical RequirementsCE Requirements Initial SetupPlumbing Requirements Initial Setup Adjusting Brew VolumesCoffee Brewing CleaningFilter Holder Brew cycle will not start No water TroubleshootingProblem Probable Cause BrewerTroubleshooting Problem RemedyRefer to Service Circuit Breaker for testing procedures. See Use Bunn filters made for the U3 brewer Remove obstructionRemove and clean lime off the tank heater. See Component Access ServiceContents Wire Models and 440V Four Wire Models ServiceLocation Contactor ContactorService Contactor Control Thermostat Fuse and Fuse Hilder Limit Thermostat Limit thermostatModel Voltage Reconnect the blue wire to T1 on the liquid level boardLiquid Level Board and Level Probe Jumper Not TouchingLiquid Level Board Terminals Test Procedures Disconnect the brewer from the power source ON/OFF SwitchBLK from Main Harness RED to Main Harness Pump Assembly Pump AssemblyRelay Brewers W/BREW Lockout If voltage is present as described, proceed to #3Brew Timer Removal and Replacement Disconnect the wires from the relayRefer to and reconnect the wires BLU from Start Switch BLU to Start Switch BLU from Brew TimerSelector Switch Half Batch Option Selector Switch Half BATCHP1317.30Solenoid SolenoidEarly Models Start Switch Brew Start Switch BrewTank Heaters Tank HeaterTimer Early Models Thermal Fuses 230V-CE Models onlyIf voltage is present as described, proceed to #8 Service Timer Early ModelscontDisconnect the black and white wires to the pump Harness BLK to Pump Lead WHI to Pump LeadAdjust the timer as described below Timer Setting Service Digital Timer Late ModelsIf voltage is as described, proceed to #7 Digital Timer Terminals Transformer Remove the transformer and discardService Master ON/OFF Switch Late Models Master ON/OFF Switch LOC120/208 Volts AC 120/240 Volts AC 3 Wire + GND Single Phase 10060 080900 10060 080900 Schematic Wiring Diagram U3A CE Schematic Wiring Diagram U3833 Schematic Wiring Digram U3833

U3A, U3 specifications

Bunn U3A, also known as Bunn's U3A, is a unique and innovative approach to education that caters specifically to retirees and senior citizens. The primary aim of this initiative is to foster lifelong learning and social engagement among older adults, empowering them to explore various subjects of interest and connect with like-minded individuals.

One of the main features of Bunn U3A is its diverse range of courses and activities. From art and music appreciation to digital literacy and gardening, participants can choose from a variety of subjects that pique their interest. This broad curriculum is designed to cater to varied backgrounds and skill levels, ensuring that everyone finds something that resonates with them. The courses are typically led by volunteer tutors, many of whom are retired professionals passionate about sharing their knowledge and experiences.

Another characteristic of Bunn U3A is its strong emphasis on community and socialization. By providing a supportive and welcoming environment, members are encouraged to interact, collaborate, and form friendships. The organization often hosts events, workshops, and excursions, further enhancing the sense of belonging and camaraderie among participants. This communal aspect is crucial for combating feelings of isolation that can sometimes accompany retirement.

Bunn U3A leverages technology to enhance the learning experience. Many courses integrate digital tools and online platforms, enabling participants to access resources and engage in discussions beyond the classroom. This tech-savvy approach ensures that members are equipped with essential skills that are increasingly relevant in today’s digital world. As a result, participants often find themselves not only enriching their knowledge but also enhancing their technological proficiency.

In addition to its educational offerings and community focus, Bunn U3A promotes a culture of inclusivity. Everyone, regardless of previous academic background, is welcomed to join, emphasizing that learning is a lifelong journey. The philosophy that underpins Bunn U3A is one of empowerment, with a commitment to ensuring that older adults continue to thrive intellectually, socially, and emotionally.

In summary, Bunn U3A stands out as a vibrant learning community that prioritizes the educational and social needs of retirees. With its diverse courses, strong community bonds, and integration of technology, it serves as a model for how organizations can successfully promote lifelong learning and engagement among older individuals, enriching their lives in meaningful ways.
Top Page Image Contents