Bunn VPR APS service manual Electrical Requirements, Initial SET-UP, Coffee Brewing, Cleaning

Page 4

ELECTRICAL REQUIREMENTS

CAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up.

The brewer has an attached cordset and requires 2-wire grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz.

INITIAL SET-UP

CAUTION - The brewer must be disconnected from the power source throughout the initial set-up, except when specified in the instructions.

1.Insert an empty funnel into the funnel rails.

2.Place an empty dispenser under the funnel.

3.Pour three pitchers of tap water into the screened area on top of the brewer. Allow approximately two minutes between pitchers for water to flow into the tank. While the third pitcher of water is entering the tank, the tank will fill to capacity and the excess will flow from the sprayhead, out of the funnel, and into the dispenser.

4.When the flow of water from the funnel stops, connect the brewer to the power source and wait approxi- mately twenty minutes for the water in the tank to heat to the proper temperature. Some water will drip from the funnel during this time; this is due to expansion and should not occur thereafter.

5.Empty the dispenser and replace it under the funnel.

6.Pour one pitcher of tap water into the screened area on top of the brewer.

7.When water has stopped flowing from the funnel let water in the tank reheat to the proper temperature.

8.Empty the dispenser. The brewer is now ready for use in accordance with the coffee brewing instructions below.

NOTE: The control thermostat will need to be adjusted downward to compensate for high altitudes. Refer to Steaming and spitting around the funnel on page 5 for instructions.

COFFEE BREWING

1.Insert a BUNN® filter into the funnel.

2.Pour the fresh coffee into the filter and level the bed of grounds by gently shaking.

3.Slide the funnel into the funnel rails.

4.Place an empty dispenser beneath the funnel.

5.Pour one pitcher of tap water into the screened area on top of the brewer.

6.When brewing is completed, simply discard the grounds and filter.

CLEANING

1.The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment.

2.Check and clean the sprayhead. The sprayhead holes must always remain open.

3.With the sprayhead removed, insert the deliming spring (provided) all the way into the sprayhead tube. When inserted properly, no more than two inches of spring should be visible. Saw back and forth five or six times.

NOTE – In hard water areas, this may need to be done daily. It will help prevent liming problems in the brewer and takes less than a minute.

Page 4

39064 042806

 

Page 3 Page 5
Image 4
Page 3 Page 5
Contents VPR TC VPR APS Introduction BUNN-O-MATIC Commercial Product WarrantyReturn Policy User Notices AvertissementCleaning Electrical RequirementsInitial SET-UP Coffee BrewingTroubleshooting Problem Probable Cause RemedyProblem Probable Cause Water TemperatureProblem Probable Cause RemedyComponent Access ServiceControl Thermostat Service Limit Thermostat Tank HeaterTank Heater Terminals Volts a C Wire VPR, VPR TC & VPR APS

VPR APS specifications

The Bunn VPR APS is a commercial coffee brewer designed for businesses that require a reliable and efficient solution for brewing large quantities of coffee. This equipment is particularly well-suited for restaurants, offices, convenience stores, and other settings where high-demand for coffee is prevalent. With its robust construction and advanced brewing technology, the VPR APS ensures consistent flavor and quality with every batch.

One of the standout features of the Bunn VPR APS is its capacity. The machine can brew up to 3.8 gallons of coffee per hour, making it capable of keeping up with busy service demands. The unit is equipped with two glass decanters, allowing users to have a ready supply of freshly brewed coffee on hand. Additionally, the VPR APS comes with an automatic faucet, which enables easy serving of coffee straight from the brewer into cups or containers, promoting efficiency during peak hours.

The Bunn VPR APS utilizes a unique brewing technology known as the "infusion series," which optimizes the coffee extraction process. This system allows for precise control over water temperature and flow rate, ensuring that the coffee is brewed at the ideal conditions. This level of control not only enhances the flavor profile of the coffee but also contributes to the consistency across different brews.

Another important characteristic of the Bunn VPR APS is its user-friendly interface. The machine is designed with ease of use in mind, featuring intuitive controls and simple operation. This allows staff to quickly learn how to use the machine, minimizing downtime and maximizing productivity.

Moreover, the Bunn VPR APS is constructed with durability in mind. Its stainless steel exterior not only gives it a professional appearance but also makes it resistant to rust and wear. This sturdiness ensures that the machine can withstand the rigors of a busy commercial environment.

Convenience is further enhanced with the Bunn VPR APS's ability to be plumbed or operated with a portable water tank, providing versatility based on the needs of the establishment.

In summary, the Bunn VPR APS stands out in the market for its high brewing capacity, advanced extraction technology, ease of use, durability, and versatility. It's an ideal choice for businesses looking to serve high-quality coffee efficiently.
Top Page Image Contents