Initial SET-UP, Electrical Requirements

INITIAL SET-UP

NOTE: This refill unit should not be used to initially fill the hopper. Running the motor for extended periods will trip the thermal switch. The thermal switch will reset, but requires up to 30 minutes of cooling time.

NOTE: Hoses, clamps and product container connectors are not supplied. Fittings and labels are supplied. Make hose assemblies as required.

1.Assemble hoppers with probe housing assemblies to CDS-2, CDS-3 or modify existing hoppers using tem- plate provided.

2.Make sure probe housing assembly is pushed down into slots on back of hoppers.

3.Install cable assembly to the lower right front of the auto refill box and the probe housing assemblies on the hoppers. The connectors on the cable pushes in and cap rotates 1/4 turn to lock into position.

4.Run output tubes from auto refill box to the quick disconnects in the hoppers.

NOTE: Make sure numbers on the labels match up. Cable#1 with Hose#1, Cable#2 with Hose#2...ect.

5.Connect one end of input hoses to the auto refill box and the other end to the product container. Product container connectors (BIB) are not supplied. Install your own interface.

NOTE: Make sure all connections are made before connecting the auto refill box to the power source.

6.Each product container has an ON/OFF refill switch located on the front of the auto refill box. A second switch for each hopper is at the probe housing assembly. These are 3 position switches, high level, low level and a center “OFF” position.

7.Place the main ON/OFF switch and ON/OFF refill switches in the “OFF” position.

8.Make sure all hoses are connected. Connect the dispenser to the power source and place the main ON/OFF switch in the “ON” position.

9.Place one of the ON/OFF refill switches in the “ON” position, after a four second delay product will begin to flow through the hoses into the hopper. Be sure the switch selected is filling the correct hopper, if not, check the labels. See NOTE in step #4.

10.To test refill circuit short out probes on one of the hoppers with a screwdriver, that hopper should shut off, remove the screwdriver and the hopper will start to fill again after a four second delay. If hopper does not start to fill, check labels, refer to NOTE in step #4.

ELECTRICAL REQUIREMENTS

CAUTION - The dispenser must be disconnected from the power source until specified in Initial Set-Up.

The 120 volt version of this dispenser has an attached cordset and requires 2-wire, grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz. The mating connector must be a NEMA 5-15R.

The 200 volt or 240 volt versions require 2 wire, grounded service rated 200 volts ac or 240 volts ac, single phase, 50 Hz.

(Refer to the dispenser’s data plate for exact voltage requirement.)

Electrical Hook-Up

CAUTION – Improper electrical installation will damage electronic components.

1.An electrician must provide electrical service as specified.

2.Using a voltmeter, check the voltage and color coding of each conductor at the electrical source.

3.Connect the dispenser to the power source.

3	28791.1 011500

AF PR-3 specifications

The Bunn AF PR-3 is a high-performance coffee brewer designed for commercial use, particularly in cafés, restaurants, and other settings where quality coffee must be brewed quickly and efficiently. Known for its exceptional reliability and innovative features, the Bunn AF PR-3 has become a popular choice among coffee professionals.

One of the standout features of the AF PR-3 is its ability to brew up to 3 gallons of coffee per hour. This capacity makes it ideal for busy environments where a quick turnaround is essential. The brewer uses a patented technology that ensures optimal brewing temperature and extraction time, resulting in a rich, full-bodied flavor profile in each cup.

Another significant aspect of the Bunn AF PR-3 is its automatic features. With a programmable digital display, users can easily select brew settings and adjust individual preferences. This user-friendly interface simplifies operation and allows baristas to focus on crafting the perfect coffee every time. The unit also comes with a built-in hot water faucet that enables the brewing of other beverages, such as tea or instant soups, further enhancing its versatility.

Additionally, the Bunn AF PR-3 incorporates advanced brewing technology, including its unique "infusion" brews system. This system allows water to saturate coffee grounds evenly, promoting even extraction. As a result, the coffee brewed with the AF PR-3 exhibits a well-balanced taste with vibrant aroma, catering to the sophisticated palate of coffee aficionados.

Durability is another characteristic of the Bunn AF PR-3. The brewer is built with high-quality stainless steel, making it resistant to wear and tear, and ensuring that it can withstand the demands of a bustling café environment. The machine's components are designed for easy maintenance, allowing operators to clean and service the brewer with minimal downtime.

Moreover, the Bunn AF PR-3 is energy efficient, designed to reduce energy consumption without compromising performance. This feature not only helps in keeping operational costs down but also makes it an environmentally friendly choice for coffee businesses.

In conclusion, the Bunn AF PR-3 is a leading coffee brewer that combines speed, quality, and user-friendly technology, making it an essential piece of equipment for any commercial coffee establishment. Its ability to brew large quantities of rich, flavorful coffee efficiently, along with its durability and ease of operation, solidifies its position as a top contender in the coffee brewing market.