Initial SET-UP TB3/TB3-LP only | Bunn TB3 Series specs

41465 082208

INITIAL SET-UP (TB3/TB3-LP ONLY)

CAUTION - The brewer must be disconnected from the power source throughout the initial set-up, except when specified in the instructions.

1.Remove the top lid from the brewer.

2.Rotate the control thermostat knob fully counterclockwise to the "OFF" position and replace the top lid.

3.Set the delay dial on the timer at three minutes and set the dilution dial at three to four minutes.

4.Remove the metal discharge tip from the funnel to speed up the set-up procedure. Insert the empty funnel into the funnel rails.

5.Place an empty dispenser on the brewer base. Be sure the funnel discharge is directly above the hole in the dispenser top lid.

6.Plug in the brewer and place the ON/OFF switch in the "ON" position. Momentarily press the start switch. Water will flow into the tank and will shut off after three minutes. Press the start switch again. During the second period, the tank will fill to its capacity and the excess will flow from the funnel into the dispenser.

7.Place the ON/OFF switch in the "OFF" position.

8.Disconnect the brewer from the power source and remove the top lid.

9.Rotate the control thermostat knob fully clockwise to the "ON" position and replace the top lid.

10.Plug in the brewer and wait for the water in the tank to heat to the proper temperature (approximately 20 minutes). Some water will drip from the funnel during this time; this is due to expansion and should not occur thereafter.

11.Place the ON/OFF switch in the "ON" position and press the start switch. Empty the dispenser after water has stopped flowing from the funnel.

12.Allow the water in the tank to reheat to the proper temperature.

13.Place the ON/OFF switch in the "ON" position and press the start switch.

14.Place the ON/OFF switch in the "OFF" position immediately after water stops flowing from the funnel. Check the water volume in the dispenser. It should be seventy-six ounces.

15.If not, adjust the digital timer as required. See Adjusting Brew Volumes on page 5, and measure another concentrate cycle.

16.Repeat steps 12-15 until the proper water volume is achieved.

17.Unplug the brewer and remove the top lid.

18.Set the delay dial on the timer at three minutes and empty the dispenser.

19.Place the ON/OFF switch in the "ON" position, momentarily press the start switch, and allow both the con- centrate and dilution cycles to occur.

20.When all water stops flowing, check the water volume in the dispenser. It should be 396 ounces.

21.If not, unplug the brewer and remove the top lid.

22.Adjust the dilution dial on the timer as required. Replace the top lid, plug in the brewer, start, and measure another brew cycle.

23.Repeat steps 19-22 until the proper water volume is achieved.

24.Return the delay dial on the timer to eight minutes. Replace the top lid and plug in the brewer.

25.Reinstall the metal discharge tip into the funnel.

26.Load the funnel with a BUNN® paper filter and approximately four ounces of loose tea leaves.

27.Place the ON/OFF switch in the "ON" position, momentarily press the start switch, and allow both the con- centrate and dilution cycles to occur. Observe the funnel discharge and the dilution streams near the end of the brew cycle. The dilution stream should stop approximately thirty seconds after the funnel discharge has stopped.

28.If not, unplug the brewer and remove the top lid.

29.Adjust the delay dial on the timer as required. Replace the top lid and plug in the brewer.

30.Repeat steps 26-29 until the proper dilution timing is achieved.

Page 8

TB3 Series specifications

The Bunn TB3 Series is a prominent line of commercial coffee brewers designed to meet the demands of busy coffee shops, restaurants, and offices. With its innovative features and robust design, this series is tailored for those who prioritize quality and efficiency in coffee brewing.

One of the standout characteristics of the Bunn TB3 Series is its ability to brew large quantities of coffee quickly, making it an ideal choice for high-volume environments. The TB3 model can brew up to 3.8 gallons of coffee per hour, ensuring that fresh coffee is always available for customers or staff. This impressive brewing speed is complemented by a unique design that incorporates a high-performance water tank, which maintains a ready-to-brew temperature for optimal extraction.

The TB3 Series utilizes advanced technology to enhance the brewing process. The brewer is equipped with a digital brew control system that allows for precision in adjusting brew times and temperatures. This technology ensures consistent quality in every cup, regardless of varying conditions. Additionally, the digital display provides real-time feedback, making it user-friendly and easy to operate.

Furthermore, the Bunn TB3 Series features a stainless-steel construction that not only provides durability but also facilitates easy cleaning. The sleek design is complemented by a compact footprint, which is crucial in environments where space is limited. It incorporates a large, removable drip tray that helps to manage spills, ensuring a clean and professional look at all times.

Another notable feature is the brewer’s ability to accommodate different brew methods, such as batch brewing and single-serve systems. This versatility allows businesses to cater to various customer preferences and try different coffee blends.

The Bunn TB3 Series is designed with user convenience in mind. It has a simple and intuitive interface, enabling operators to quickly learn how to use the machine effectively. Additionally, the model is equipped with safety mechanisms such as an overflow protection system to prevent spills and maintain a clean workspace.

In summary, the Bunn TB3 Series represents a perfect blend of efficiency, versatility, and durability. With its rapid brewing capabilities, advanced technology, and user-friendly features, it serves as a reliable coffee brewing solution for any commercial setting, making it a favorite among coffee professionals and enthusiasts alike.