Initial SET-UP TB3Q/TB3Q-LP/TB6Q only | Bunn TB3-LP instruction

Brew water temperature is factory set at 205° F (96.1° C) Areas of high altitude will require lowering this tempera- ture to prevent boiling. This chart should be used as a guide when readjusting the brew water temperature.

INITIAL SET-UP (TB3Q/TB3Q-LP/TB6Q ONLY)

CAUTION - The brewer must be disconnected from the power source throughout the Initial Set-Up, except when specified in the instructions.

1.Remove the top cover from the brewer.

2.Rotate the control thermostat knob fully counterclockwise to the "OFF" position and replace the top lid.

3.Insert an empty funnel into the funnel rails. On TB6Q models, rotate the funnel handle left or right to align the funnel discharge over the reservoir.

4.Place an empty dispenser on the brewer base. Be prepared to empty the dispenser during these initial steps. Be sure funnel discharge is directly above the dispenser.

5.Plug in the brewer, place the ON/OFF switch in the "ON" position ("SWEET" or "UNSWEET" position for models with a sweetener option) (LEFT or RIGHT on TB6Q), and momentarily press the START switch. Water will flow into the tank and dispenser for three and one-half minutes. Empty the dispenser when this first cycle stops and press the START switch again. Empty the dispenser when the second cycle stops and press the START switch once more. During the third cycle, the tank will fill to its capacity and the excess will flow from the funnel into the dispenser. Empty the dispenser when this third cycle stops.

6.Begin another brew cycle and measure the total water volume from the dispenser. It should be approximately 3 gallons and 12 ounces. (396 ounces). CONCENTRATE MACHINES WILL YIELD ONLY 76 OZ.

7.If not, adjust the timer as required. See Adjusting Brew Volumes.

8.Unplug the brewer, remove the top lid, rotate the control thermostat knob fully clockwise to the "ON" position and replace the top lid.

9.Empty the dispenser.

10.Plug in the brewer and wait for the water in the tank to heat to brewing temperature (approximately 20 minutes). Some water will drip from the funnel during this time; this is due to expansion and should not occur thereafter.

11.Begin another brew cycle. Empty the reservoir after water has stopped flowing from the funnel.

12.Allow the water in the tank to heat to the proper tem-

perature.

13. The brewer is now ready to brew approximately 3 gallons of freshly brewed room temperature tea from three to five ounces of loose leaves.

	Altitude	Boiling point		Recommended
		of water		water temperature
	(Feet)	° F	° C	° F	° C

-1000		213.8	101.0	200	93.3
-500		212.9	100.5	200	93.3
0		212.0	100.0	200	93.3
500		211.1	99.5	200	93.3
1000		210.2	99.0	200	93.3
1500		209.3	98.5	200	93.3
2000		208.4	98.0	200	93.3
2500		207.4	97.4	200	93.3
3000		206.5	96.9	199	92.8
3500		205.6	96.4	198	92.2
4000		204.7	95.9	197	91.7
4500		203.8	95.4	196	91.1
5000		202.9	94.9	195	90.6
5500		201.9	94.4	195	90.6
6000		201.0	93.9	194	90.0
6500		200.1	93.4	193	89.4
7000		199.2	92.9	192	88.9
7500		198.3	92.4	191	88.3
8000		197.4	91.9	190	87.8
8500		196.5	91.4	189	87.2
9000		195.5	90.8	188	86.7
9500		194.6	90.3	187	86.1
	10000	193.7	89.8	186	85.6
Page 6					41465.1	040609
					41465.1	040609

TB3Q, TB3Q-LP, TB3-LP, TB6Q, TB6 specifications

The Bunn TB6Q, TB3-LP, TB6, TB3Q, and TB3Q-LP coffee brewers are a popular series of commercial machines designed for high efficiency and optimal performance in busy environments such as cafes, restaurants, and offices. These machines are crafted with a focus on quality, dependability, and advanced brewing technology to deliver a superior coffee experience.

One of the standout features across the Bunn TB series is the ability to brew large quantities of coffee quickly. The TB6Q, for instance, can brew up to 6 gallons of coffee per hour. This high volume brewing capability ensures that establishments can keep up with demand, especially during peak hours. Additionally, the machines come with a unique design that incorporates a pre-infusion feature, allowing for the coffee grounds to be evenly saturated before brewing begins, enhancing the flavor extraction process.

The TB3-LP model is designed for low-profile applications where counter space may be limited. Despite its compact design, it still offers impressive performance, brewing up to 3.8 gallons per hour. The low-profile feature makes it an ideal choice for settings that require efficiency and space optimization without compromising on the quality of the brew.

Another notable member of the series, the TB3Q and TB3Q-LP, feature a quick brew ratio, allowing users to brew up to 3 gallons of coffee in just a few minutes. These models are equipped with easy-to-use controls for simplified operation, making them perfect for staff training and user accessibility.

All models in the TB series include a hot water faucet, allowing users to dispense hot water for tea or other hot beverages quickly. This versatility adds significant value, especially in multi-beverage settings.

Regarding durability, the Bunn TB series is constructed with high-quality materials, ensuring longevity and reliability. The machines also feature internal components that are easy to access for maintenance, thus reducing downtime and improving the overall efficiency of the machine.

In terms of technology, these brewers often incorporate advanced diagnostics to promptly identify service needs or issues. The machines come with a precise brewing temperature control system that ensures each cup is brewed at the optimal temperature for maximum flavor extraction.

Overall, Bunn's TB6Q, TB3-LP, TB6, TB3Q, and TB3Q-LP coffee brewers represent the culmination of advanced brewing technology and practical design for commercial coffee solutions. Their efficiency, quality, and ease of use make them a staple in many establishments, solidifying Bunn's reputation as a leader in the coffee brewing industry.