Before you begin, Bacteria test instructions

before you begin...

1. Contents - One Bacteria Test Vial

-One Lead / Pesticide Test Packet

-One Nitrate / Nitrite Test Packet

-One pH / Hardness / Chlorine Test Packet

2. Keep tests out of reach of children or pets. Do not ingest anything from this test kit. Do not drink the

water sample used for testing.

Store and use at room temperature (60-86˚F).

Do not use on hot water or water containing bleach or detergents. Do not re-use any part of the test kit.

3. Do not open packets or vial until you are ready to perform the tests.

4. Read and follow all instructions carefully.

bacteria test instructions

1. Take out the Bacteria Test vial and set upright on a flat surface.

2. Collect water sample or turn on tap to a very slow stream.

3. Carefully twist off cap and fill vial to 1/2 inch below the top (to 5 ml line). DO NOT OVERFILL and DO NOT SPILL the bacterial growth powder in the vial.

4.Replace the cap and twist on tightly. Shake the vial vigorously for 20 seconds.

5.Place the capped vial upright in a warm area (70-90˚F) where it cannot be disturbed for 48 hrs.

6.After 48 hrs., observe the color of the liquid without

bacteria test instructions cont.

opening the vial:

Purple Color: Negative Result (No bacteria were detected)

Yellow Color: Positive Result (It is highly likely that potentially harmful bacteria were detected)

7.For positive results, add bleach to the sample before pouring down the toilet, then wash hands carefully. Negative samples may be poured directly into the toilet. Discard vial in the trash.

lead / pesticide test instructions

The Lead Test can detect dissolved lead at levels below the EPA Action level of 15 parts per billion (ppb). The Pesticide Test detects two of the most common pesticides used in the US at or below the EPA Maximum Contaminant Level (atrazine - 3 ppb, and simazine – 4 ppb).

1. Open Lead / Pesticide packet and take out all contents. The packet contains a test vial, a dropper pipette, two test strips, and a desiccant (to be discarded).

2. Using dropper, place exactly TWOdropper-fulsof water sample into test vial. To pick up sample, tightly squeeze the bulb at the end of the dropper and place the open end into water sample. Release the bulb to pick up sample, then squeeze again to expel sample into vial.

3. Swirl vial gently for several seconds. Place on

lead / pesticide test instructions cont.

a flat surface.

4.Place both test strips into the test vial, with arrows pointing DOWN.

5.Wait 10 minutes. Do not disturb strips or vial during this time. Blue lines will appear on the strips.

6.Take the strips out of the vial and read results.

Negative: Bottom line (next to number 1) is darker than top line (next to number 2).

If you only see one line	11	22
next to number 1, the test
is negative.	11	22

Positive: Top line (next to number 2) is darker than bottom line (next to number 1), or lines are equally dark.

				11		22

				11		22

7.Note: If no lines appear, or both lines are very light, the test did not run properly and the result is not valid.

If a test strip shows a positive result, your water sample may contain lead or pesticides at a toxic level.

nitrate / nitrite test instructions

1. Carefully open Nitrate / Nitrite Test packet and take out test strip.

WT1 specifications

The BRK Electronic WT1 is a groundbreaking device in the field of smoke detection technology, offering advanced features and enhanced safety for homeowners and businesses alike. This state-of-the-art smoke alarm incorporates a variety of cutting-edge technologies that ensure reliable detection of smoke and fire hazards.

One of the standout features of the WT1 is its photoelectric sensor, which is designed to detect smoldering fires more quickly than traditional ionization smoke detectors. This technology significantly reduces false alarms triggered by non-threatening sources, such as cooking smoke or steam, offering a more accurate assessment of potential fire hazards. As such, the WT1 is ideal for a wide range of environments, including kitchens and living spaces where cooking activities are common.

Additionally, the BRK Electronic WT1 boasts a sleek and modern design that fits seamlessly into any interior decor. Its low-profile appearance ensures that it remains unobtrusive while still being effective as a safety device. The user-friendly interface, complete with an intuitive LED indicator, allows for easy operation and instant alerts for both smoke detection and device status.

Another remarkable aspect of the WT1 is its ability to function in a wide range of temperatures and humidity levels, ensuring optimal performance in various environmental conditions. The device is engineered to be more resistant to corrosion and dust, extending its lifespan and reliability.

The WT1 also features a built-in test/hush button, allowing users to easily test the alarm functionality and silence it during non-threatening situations. This feature is particularly beneficial for households with pets or during cooking, ensuring that users can maintain a peaceful home environment without compromising safety.

Furthermore, the BRK Electronic WT1 is equipped with a long-lasting lithium battery that extends the life of the alarm and reduces the need for frequent replacements. This energy-efficient design not only helps users save money but also minimizes waste.

In conclusion, the BRK Electronic WT1 smoke alarm represents a significant advancement in fire safety technology. With its photoelectric sensing, sleek design, and user-friendly features, it provides peace of mind to homeowners and businesses by ensuring that they are well-protected against potential fire risks. Whether installed in new constructions or used as a replacement for older models, the WT1 sets a new standard for smoke detection technology, making it a smart choice for anyone looking to enhance their safety measures.