ECDFPW314C ECDFPWVR314C Installation Instructions

ECDFPW314C ECDFPWVR314C

INSTALLATION INSTRUCTIONS

1. Wall should already be framed for the fountain using the positioning dimensions shown in Figure 3. Shown dimensions pertain to installation location (framing must support up to 300 lbs. weight). These dimensions are required for compliance with ANSI Standard A117.0.

2. Attach wall plate assembly to wall as shown in Figure 3 using 5/16" x 2" long bolts and flat washers (not provided). Tighten securely. (Fastener must match wall type, i.e. lag screws for wood studs, bolts and anchors for masonary construction.)

3. Install back panel. Place the upper edge of the panel above hanger on the wall. Slide panel down until it engages the hanger. Be sure back panel is firmly engaged before releasing it.

4. Install rough-in plumbing as shown in Figure 3. Waste line should extend a minimum of 2" (51mm) thru the back panel. Run supply water inlet line thru back panel. Install a service stop (not provided). Turn on supply water and flush thoroughly.

5. Remove bottom access panel from fountain basin and save the screws. Install the fountain to the back panel using (4) 5/16" x 3/4" long screws and washers (provided) thru holes in back panel. Tighten securely.

6. Cut waste tube to required length using plumbing hardware and a trap (not provided) as a guide. Install hardware and trap. Tighten securely.

7. Make water supply connections from service stop to the 3/8" O.D. unplated copper tube coming out of the fountain strainer (See Fig. 1). Turn on water supply and check for leaks. Newly installed water supply line should be insulated after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER

AS DAMAGE TO THE O-RINGS MAY RESULT.

8.These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is above 105 PSIG, a pressure regulator must be installed in the supply line. Any damage caused by reason of connecting these products to supply line pressure lower than 20 PSIG or higher than 105 PSIG is not covered by warranty.

9.Check stream height from bubbler. Stream height is factory set at 35 PSI. If supply pressure varies greatly from this, adjust the screw on regulator item 10 by using a small screwdriver through the small hole

in the push button item 3 (See Fig.5). Clockwise adjustment will raise stream height and counter-clockwise adjustment will lower stream height. For best adjustment stream should hit basin approximately 6-1/2" (165mm) from bubbler.

10.Replace bottom access panel to fountain basin using screws provided. Tighten securely.

TROUBLE SHOOTING AND MAINTENANCE

1. Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits may be removed from orifice with a small round file not over 1/8" diameter or a small diameter wire. CAUTION: Do not file or cut orifice materials.

2. Stream Regulator: If orifice is free of material deposits, regulate flow according to instruction 9 stated above.

3. Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize an o-ring water seal. To remove tubing from the fitting, relieve water pressure, push in on the gray collar while pulling on the tubing (See Figure 2). To insert tubing, push tube straight into the fitting until it reaches a positive stop, approximately 3/4".

PAGE 3

97749C (Rev. J - 7/07)

ECDFPW specifications

The Elkay ECDFPW is a sophisticated drinking water fountain designed to meet the demands of modern environments while promoting sustainability and health. This innovative product stands out due to its combination of advanced technologies and user-friendly features, making it a preferred choice for schools, parks, workplaces, and public spaces.

One of the most notable features of the Elkay ECDFPW is its integrated water bottle filling station. This convenient addition allows users to easily refill reusable water bottles, significantly reducing the reliance on single-use plastic bottles. The Smart Water Technology incorporated in the fountain ensures that the water is not only clean but also chilled, enhancing the drinking experience. The flow rate is optimized to fill bottles efficiently while minimizing water spillage.

The ECDFPW utilizes a front-mounted bottle filler, allowing for easy access and usability, particularly in high-traffic areas. The design prioritizes hygiene, with a hands-free sensor activation that minimizes contact. This feature is particularly valuable in today’s health-conscious society, reducing the risk of germ transmission.

Further enhancing its appeal, the Elkay ECDFPW is equipped with a Filtered Water System. This technology employs a specialized filtration process to ensure the water delivered is free from contaminants, providing assurance regarding water quality. The filter status indicator informs users when the filter requires replacement, ensuring ongoing access to clean water.

In terms of build characteristics, the Elkay ECDFPW showcases a robust, durable construction made from high-quality materials that resist corrosion and wear. It is designed for easy installation and maintenance, with provisions for mounting that adapt to various settings. The unit is ADA-compliant, ensuring accessibility for all users, including those with disabilities.

Sustainability is at the forefront of the Elkay ECDFPW’s design. Each fountain is part of a broader initiative to promote eco-friendly practices, such as reducing plastic waste and conserving water. With an array of stylish finishes and configurations, Elkay allows customization for matching the aesthetic of any installation environment.

In summary, the Elkay ECDFPW merges practicality with innovative technology, offering users a cleaner, healthier hydration experience. Its features like hands-free operation, integrated filtration, and a focus on sustainability make it a standout choice among drinking water solutions. As public spaces continue to embrace healthier options, the Elkay ECDFPW is paving the way for a greener future.