Extron electronic APP, P/2 DA 2 WM/EC Easy setup procedure, Installing the mounting bracket

Page 7

Controls and Installation, cont’d

Installing the P/2 DA2 WM/EC

Easy setup procedure

The wall-mounted P/2 DA2 WM kit consists of the faceplate/distribution amplifier assembly and a mounting bracket which mounts in a wall opening and to which the faceplate assembly is attached. The P/2 DA2 EC kit consists of the faceplate/distribution amplifier assembly which mounts in the Euro Channel raceway.

1

For wall mounting only: Using the mounting

 

template provided in the “Appendix” as a guide,

 

carefully cut a mounting hole through the wall where

 

the mounting bracket is to be installed.

 

For wall mounting only: Install the mounting bracket

2

 

using the supplied screws and mounting clips. Refer

 

to the section “Installing the mounting bracket” for

 

further details.

 

Before connecting any cables, power off all

3

 

equipment. If the optional Architectural Adapter

 

Plate (AAP) is being installed, please refer to

 

“Installing Architectural Adapter Plates” in this chapter.

 

The rear connectors are the same for both WM and

4

 

EC models. Please refer to figure 2-3. Connect the

 

VGA output cable to the 15-pin HD female output

 

connector. To prevent installation debris or objects

 

from entering the opening in the sheet metal just

 

above this VGA connector, it is suggested that some

 

masking tape be used to temporarily cover this

“Euro Channel installation” section.

6Power up all of the input and output devices.

7The image should now display on screen. If it does not, double check steps 3 through 6 and make adjustments as needed. Refer to the section “Setting the DIP switches” in this chapter.

8For the P/2 DA2 WM, attach the P/2 DA2 WM to the wall mounting bracket (see “P/2 DA2 WM wall installation”).

For the P/2 DA2 EC, attach the P/2 DA2 EC to the Euro Channel (see “P/2 DA2 EC Euro Channel installation”).

Installing the mounting bracket

The wall-mounted P/2 DA2 WM kit includes a mounting bracket which is installed in a wall opening. The AAP version of the P/2 DA2 WM uses a wider mounting bracket, as shown below.

1.Once the proper wall location for mounting the distribution amplifier has been selected, cut an opening in the wall using the proper mounting template found in the “Appendix” section.

2.Using two supplied screws and mounting clips, attach the mounting bracket to the hole opening, as shown below.

opening. Remove this tape after installation is

completed. Next, if there is audio output, connect

the audio output cable to the 3.5 mm captive screw

connector. Finally, connect the power cable to the

power input connector. Refer to the “Cabling” and

“Connecting audio” sections of this chapter.

5 Before attaching the faceplate assembly to the wall

mounting bracket/Euro Channel, attach the

computer video cable to the 15-pin HD female input

Backing Clip can be in either orientation.

See Detail A or Detail B.

Mounting Bracket

wall mounting bracket

Backing Clip can be in either orientation.

See Detail A or Detail B.

Mounting Bracket

Sheet Rock

wall mounting bracket

for Architectural Adapter Plate

connector on the faceplate. Next, a local monitor

may be connected to the 15-pin HD female buffered

local monitor output connector on the faceplate.

Finally, for audio input, connect the audio cable to

the faceplate’s 3.5 mm audio input jack. Refer to the

“Cabling” and “Connecting audio” sections of this

chapter. For Euro Channel applications, refer to the

Sheet Rock

 

Backing Clip

Backing Clip

0.75" #6-32 Screw

1.25" #6-32 Screw

Mounting Bracket

Mounting Bracket

Detail A

Detail B

Figure 2-4 — Installing the mounting bracket

2-4

P/2 DA2 WM/EC Controls and Installation

P/2 DA2 WM/EC Controls and Installation

2-5

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Distribution Amplifier User’s ManualExtron’s Warranty PrecautionsFCC Class a Notice Table of Contents One About the P/2 DA2 WM/EC and P/2 DA2 FeaturesFront faceplate Controls and InstallationRear connectors Front and Rear PanelsInstalling the mounting bracket Easy setup procedureConnecting audio output Controls and Installation, cont’dCabling Balanced audio Installing Architectural Adapter PlatesDA2 EC Euro Channel installation DA2 WM wallmount installationSetting the DIP switches AAppendix Appendix DA2 WM/EC Specifications Figure A-1 WM model faceplate dimensions Appendix, cont’d DA2 WM Faceplate DimensionsOptional Architectural Adapter Plates Appendix, cont’d CablesAppendix, cont’d Single Type Connector Architectural Adapter PlatesMulti Type Connector Architectural Adapter Plates Actual size MountingTemplate Shown

APP, P/2 DA 2 WM/EC specifications

The Extron Electronics APP, P/2 DA 2 WM/EC is a high-performance, dual output distribution amplifier that is specifically designed for professional audio and video applications. Ideal for various environments such as classrooms, conference rooms, and control centers, this compact and robust device ensures optimal signal integrity and reliability.

One of the main features of the APP, P/2 DA 2 WM/EC is its ability to take a single audio or video input and distribute it to two identical outputs. This feature makes it an essential tool for applications requiring multiple displays or audio systems utilizing the same source. The device supports high-resolution video signals, ensuring that the quality of the output remains pristine, regardless of the distance it must travel.

The APP, P/2 DA 2 WM/EC utilizes cutting-edge technology to maintain signal fidelity. It employs advanced circuitry designed to minimize distortion and signal loss, enabling consistent performance across varying signal conditions. The built-in features include signal amplification, which boosts input signals for powerful distribution, while the low-noise design ensures minimal interference.

Another highlight of this distribution amplifier is its versatility. It supports multiple video formats, including Composite, S-Video, and Component, making it suitable for a wide range of AV equipment. This compatibility ensures that users can integrate the APP, P/2 DA 2 WM/EC seamlessly into their existing systems, regardless of the source components being used.

The unit also comes with enhanced control options. It features a comprehensive set of integration tools that simplify installation and operation, such as remote control capabilities and diagnostic indicators. This user-friendly design helps operators easily monitor signal performance and troubleshoot any potential issues without disrupting the workflow.

When it comes to installation, the APP, P/2 DA 2 WM/EC is engineered for flexibility. Its compact form factor allows for convenient mounting in varied environments, whether on a rack or wall-mounted, optimizing space usage.

In summary, the Extron APP, P/2 DA 2 WM/EC is an exceptionally reliable and versatile distribution amplifier that offers advanced features and technologies catering to professional audio-video environments. Its robust performance, signal preservation, and user-friendly design make it an essential component for any modern AV system.
Top Page Image Contents