Filter Assembly
For best performance and results, the filter assembly must be cleaned.
The filter efficiently removes food particles from the wash water, allowing it to be recirculated during the cycle. For this reason, it is a good idea to remove the larger food particles trapped in the filter after each wash cycle by rinsing the "A" semi-circular filter and cup under running water. To remove the filter assembly, pull on the cup handle in the upward direction. The entire filter as- sembly (made up of the "A" semicircular filter and the "B" fine filter) should be cleaned at; east once a month. To clean the filter and the fine filter, use a cleaning brush. Then, reassemble the filter parts as shown in the figures below and reinsert the entire assembly in the dishwasher, positioning in its seat and pressing downward.
The dishwasher must never be used without the filters. Improper replacement of the filters may reduce the performance level of the appliance and damage dishes and utensils.
Cleaning the Spray Arms
It may happen that food particles become encrusted on the sprayer arms and block the holes (see "Close up view interior", letters C-F ). Check the sprayer arms periodically and clean them when needed.
A
B
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to allow proper installation.
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the dishwasher, making it level. In any case, the appliance should not be inclined more than 2=. If the appli- ance is level, it will help ensure proper performance.
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4 (gas) con- nector making sure that it is fastened tightly in place (see Fig.1). If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance.
same procedures as those for the connection to the cold water line.
Anti-Flooding Protection
The dishwasher is equipped with a system that stops the supply of water in the event of a problem with the water supply hose, or leaks within the unit, If for any reason the box containing the elec- trical components happens to get damaged, remove the plug from the socket immediately. In order to guarantee that the anti-flood- ing feature operates properly, the "A" box with water supply hose must be attached to the water supply tap as shown in Fig.1. No other type of connection is acceptable. The water supply hose must not,under any circumstances, be cut, as it contains electrical parts which are live. If the length of the hose is not adequate to make a proper connection, the hose must be replaced with one that is long enough. This hose is available upon request from specialised re- tailers and service centres.
It may occur that the dishwasher does not function or does not function properly. Before calling for assistance, See what can be done first: Have you forgotten to press one of the buttons or to perform an essential operation?
The dishes are not clean
Have you checked whether:
- the water is turned on and the hose is connected properly; |
- the water supply to the house is on and has sufficient pressure; |
- the water supply hose is crimped or bent; |
In this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced.
Fig.1
The dishwasher does not start
Have you checked whether:
-the plug is pushed into the socket correctly;
-the power is on in the house;
-the door is closed properly;
-the ON-OFF switch is on "ON";
-the water supply is turned on.
The dishwasher does not load water
Have you checked whether:
-the water is turned on and the hose is connected properly;
-the water supply to the house is on and has sufficient pressure;
-the water supply hose is crimped or bent;
-the filter for the water supply hose is clogged.
- the filter for the water supply hose is clogged. |
The dishwasher does not drain
Have you checked whether:
- the drain hose is crimped or bent.
Lime deposits or a white film form on the dishes
Have you checked whether:
-the lid to the salt container is closed properly;
-the rinse aid dosage is correct.
If, despite all these checks, the dishwasher still does not function and/or the problem persists, contact the nearest authorised service centre and provide them with the following information:
-the nature of the problem;
-the model and the serial number which are indicated on the plate located on the side of the inner part of the door.
Never call on unauthorised technicians and refuse to allow
parts to be installed that are not original spare parts.
Installation
Drain Hose Connection
Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it run into the sink, making sure to avoid bending or crimping it. Use the special plastic support that comes with the appliance (see Fig.2). The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water.
MAX 100 MIN 40
Fig.2
Attention:
The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain.
Electrical Connection
After making sure that the voltage and frequency values for the current in the home correspond to those on the rating plate (located on the stainless steel inner door of the appliance) and that the electrical system is sized for the maximum voltage on the rating plate, insert the plug into an electrical socket which is earthed prop- erly (the earthing of the appliance is a safety requirement man- dated by law).
If the electrical socket to which the appliance must be connected is not appropriate for the plug, replace the plug rather than using adapters or the like as they could cause overheating and burns.
