Title: H. Evaporator Assembly | Model: |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Required Number | |||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Index |
|
| Material or |
|
| to | to |
|
|
|
|
|
| |
No. | Description |
| Model Number |
| Part Number |
|
|
|
|
|
| |||
1 | Evaporator |
| - |
| 1 | 1 | 1 |
|
|
|
|
|
| |
2 |
| SS |
| 1 | 1 | - |
|
|
|
|
|
| ||
2a | T2 Screw |
| 4×8, SS |
| 2 | 2 | - |
|
|
|
|
|
| |
3 |
| SS |
| 1 | 1 | - |
|
|
|
|
|
| ||
3a | T2 Screw |
| 4×8, SS |
| 2 | 2 | - |
|
|
|
|
|
| |
4 | Heater – Defrost |
| - |
| 1 | 1 | 1 |
|
|
|
|
|
| |
5 | Thermostat – Defrost |
| - |
| 1 | 1 | 1 |
|
|
|
|
|
| |
5a | T2 Screw |
| 4×8, SS |
| 2 | 2 | 2 |
|
|
|
|
|
| |
6 | Bushing |
| - |
| 1 | 1 | 1 |
|
|
|
|
|
| |
7 | Thermistor – Defrost |
| - |
| 1 | 1 | 1 |
|
|
|
|
|
| |
7a | Thermistor – Clip |
| - |
| 1 | 1 | 1 |
|
|
|
|
|
| |
8 | “Y” Joint |
| - |
| 1 | 1 | 1 |
|
|
|
|
|
| |
9 | “Y” Joint |
| - |
| 1 | 1 | 1 |
|
|
|
|
|
| |
10 | Clip – Support Evap (A) |
| - |
|
| 1 | 1 |
|
|
|
|
|
| |
11 | Clip – Support Evap (B) |
| - |
|
| 1 | 1 |
|
|
|
|
|
| |
12 | Clip – Support Evap (C) |
| - |
|
| 2 | 2 |
|
|
|
|
|
| |
13 | Shield – Heat |
| - |
| 3A1853G01 |
| 1 | 1 |
|
|
|
|
|
|
Installation Instructions for Parts 10, 11, 12, & 13
1.The original heat shield must be removed. This can be done by lifting the evaporator up and sliding the heat shield out.
2.The new heat shield (part #13) is then installed in the rotocast drain pan.
3.The clips are then slid onto the end plate on the evaporator. Support clips (part #12) are installed onto the hairpin end of the evaporator as shown in the illustration.
4.The other support clips (parts #10 and #11) are installed on the return bend end (same side as inlet andoutlet tubes) as shown in the illustration.
NOTE: All clips are shown in the illustration in the correct orientation for installation. The parts are slid onto the evaporator bracket using the tab on the support clip.
22