3M 200a manual Emergency Stop Switch, Tape Loading/Threading

Page 19

Operation (Continued)

WARNINGS

1.Turn electrical supply off and disconnect before servicing taping heads or performing any adjustments or maintenance on the machine.

2.Do not leave machine running unattended.

3.Before turning drive belts on, be sure no tools or other objects are on the machine bed.

4.Keep hands and loose clothing away from moving belts.

5.Keep hands and clothing away from taping heads when machine is running. A box traveling through the machine causes taping head rollers to retract when box enters and extend as box leaves taping head.

6.Never attempt to work on any part of the machine, load tape or remove jammed boxes from the machine while machine is running.

7.When feeding boxes to the machine by hand, push box in from end only – DO NOT PUSH WITH HANDS ON ANY CORNER OF THE BOX.

8.Both the upper and lower taping heads utilize extremely sharp knives. The knives are located under the orange knife guard which has the 'WARNING – SHARP KNIFE" label. Before loading tape, refer to Figures 3-1 and 3-2 in Section II to identify the knife location. Keep hands out of these areas except as necessary to service the taping heads.

9.Turn drive belts "Off" when machine is not in use.

10.Failure to comply with these warnings could result in severe personal injury and/or equipment damage.

Electrical "On/Off" Switch

The box drive belts are turned on and off ("Off" button is red) with the electrical switch on the side of the machine frame.

Note – The case sealer has a circuit breaker located in the electrical control box on the lower right side of the machine frame. If circuit becomes overloaded and circuit breaker trips, see "Maintenance – Circuit Breaker", page 18.

Emergency Stop Switch

The machine electrical supply can be turned off by pressing the latching emergency stop switch. To restart machine, rotate emergency stop switch (releases switch latch) and then restart machine by pressing "I" (On) button on side of machine frame.

Tape Loading/Threading

See Section II, Pages 7 and 8

Note – If lower tape drum is mounted in alternate lower outboard position, remove taping head from machine bed by pulling straight up, insert threading needle in taping head and replace taping head. Install tape roll on drum (adhesive on tape leg up), thread tape under knurled roller on outboard mount, then attach tape to threading needle and pull tape through taping head with threading needle.

CAUTION – Taping head weighs approximately 7.2 kg [16 pounds]

without tape. Use proper body mechanics when removing or installing taping head.

14

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 3M Packaging Systems Division TypeTo Our Customers Replacement Parts and Additional ManualsTo Our Customers Table of Contents Section II AccuGlide II STD 2 Inch Taping Heads Description Contents 200a Adjustable Case Sealer Knife Warning Label Important SafeguardsStop Label Safety Instructions label, shown Up/Down/Lock Label Specifications Tape Application Leg Length Optional Box Weight and Size CapacitiesTape Roll Diameter Tape Application Leg Length StandardSet-Up Recommendations Machine Dimensions MinimumReceiving And Handling Installation and Set-UpUncrated 200a Frame Set-UpMachine BED Height BOX Size Capacity of Case Sealer 200a Case Sealer Components Left Front View OperationTape Loading/Threading Emergency Stop SwitchUpper Taping Head Box Size Set-UpBox Sealing Will occurLubrication MaintenanceBox Drive Belt Replacement Knife Replacement, Taping HeadPersonnel could result Circuit Breaker Could result Box Drive Belt Tension AdjustmentsCould result Box Drive Belt Tension Adjustment Machine Bed Infeed EndAdjustments This page is Blank Personnel could result Changing the Tape Leg Length Special Set-Up ProcedureBox and Machine Bed Height Range Refer to Figure To personnel could resultBox and Machine Bed Height Range This page is Blank Troubleshooting Guide Problem Cause Correction TroubleshootingPage Electrical Diagrams Electrical Diagrams Tool Kit Replacement Parts and Service InformationReplacement Parts Ordering Information and Service Spare PartsPart Number Option/Accessory Options/AccessoriesTo Order Parts Replacement Parts Illustrations and Parts ListsThis page is Blank 200a Adjustable Case Sealer Frame Assemblies 200a Adjustable Case Sealer Ref. No 3M Part No Description 200a Adjustable Case Sealer Ref. No 3M Part No Description 200a Adjustable Case Sealer Ref. No 3M Part No Description 200a Adjustable Case Sealer Ref. No 3M Part No Description 200a Adjustable Case Sealer Ref. No 3M Part No Description 200a Adjustable Case Sealer Ref. No 3M Part No Description 200a Adjustable Case Sealer Ref. No 3M Part No Description 200a Adjustable Case Sealer Ref. No 3M Part No Description Page Ref. No 3M Part No Description 200a Adjustable Case Sealer Ref. No 3M Part No Description Safety and Information Labels 3M Part No Description Qty Safety and Information Labels
Related manuals
Manual 62 pages 21.96 Kb

200a specifications

The 3M 200A is a versatile and high-performance air filtration product designed to enhance indoor air quality across various environments. Renowned for its effectiveness and efficiency, the 3M 200A employs cutting-edge technologies and features that cater to both residential and commercial applications.

One of the main features of the 3M 200A is its advanced filtration system. The product utilizes a HEPA (High-Efficiency Particulate Air) filter, which is capable of capturing up to 99.97% of airborne particles as small as 0.3 microns. This includes dust, pollen, mold spores, and pet dander, making it an ideal choice for allergy sufferers and those concerned about air quality. Additionally, the filter is designed to last longer than traditional filters, reducing the frequency of replacements and minimizing waste.

The 3M 200A also incorporates innovative technologies such as the Microforce filtration technology. This proprietary technology enhances the efficiency of particle capture while maintaining optimal airflow. By maximizing filter performance, the Microforce technology not only improves air quality but also reduces energy consumption, making the unit environmentally friendly.

Another significant characteristic of the 3M 200A is its user-friendly design. The product features a sleek and modern aesthetic that allows it to seamlessly blend into various interior styles. Its intuitive control panel ensures ease of use, allowing users to adjust settings with just a few taps. Furthermore, the 3M 200A is equipped with real-time air quality monitoring, providing users with valuable insights into their indoor environment.

In terms of performance, the 3M 200A operates quietly, ensuring minimal disruption during use. This feature is particularly beneficial in settings like bedrooms, offices, and hospitals, where peaceful environments are essential. Its compact size also makes it easy to position the unit in various spaces without sacrificing performance.

Overall, the 3M 200A stands out as a remarkable solution for improving indoor air quality. With its advanced filtration capabilities, innovative technologies, user-friendly design, and quiet operation, it is a reliable choice for anyone looking to breathe easier and maintain a healthier living environment. Whether used at home or in commercial settings, the 3M 200A is built to deliver optimal air purification, ensuring peace of mind for its users.
Top Page Image Contents