Jackson JPX-200, JPX-160, jpx-140 service manual

Page 6
1. Turn machine off, wait until the display is blank.
2. Open the door and hold a pencil or similar item against the door switch shaft.
3. Switch on and as soon as the display appears press the door switch shaft 5 times within 4 seconds.
4. The display should change to “rinse overlap”, thus showing you are in the Engineering Mode.
Scrolling through the menu is achieved by use of the two switches mentioned above; it must be switched off (“down” position) to stop the scrolling.
DANGER: DO NOT start the FILL test or the WASH PUMP test by pressing the door switch button. Close the door instead because water will start spraying.
NOTE: If it is necessary to abandon a test or other operation in the Service Mode, or when you wish to revert to normal use, switch OFF and ON again.
3
TO ENTER ENGINEERING MODE:
The “mode” switch is used to scroll between menu options and variable values.
TO ENTER ENGINEERING MODE WITHOUT REMOVING THE TOP PANEL:
IMPORTANT: To avoid wasting chemicals, remove tubes from soap and rinse-agent bottles before using the Service Mode. The sys- tem will always give an initial dose during the first cycle after switch-on, even though the wash tank may still be full.
I
N
S
T
R
U
C PREPARATION: Open the door and observe at the top right of the door frame. Notice the door switch shaft by which the door switch T is operated. This serves as the “enter” button.
I
O
N
S
In general, it should not be necessary to alter the machine settings. The factory settings have been established to give the best results.
CHEMICAL TIMER ADJUSTMENTS
This page does not apply to the JPX-140 dishmachine.
Page 5 Page 7
Image 6
Page 5 Page 7
Contents HOT Water Sanitizing Undercounter Dishmachines This page intentionally left blank Table of Contents Installation Instructions Jackson technical service if there are any questionsChemical Dispensing Equipment To Prepare Pumps for OperationPage Chemical Timer Adjustments JPX-160Operation Instructions Filling the Wash TUBJPX-160 PC Board Troubleshooting Section Problem The tank only fills up very slowlySpecifications of the JPX-140 Dimensions of the JPX-140 Front Assembly QTY DescriptionElectrical Panel Front and Bottom View Rinse Tank Wash ARM/RINSE ARM Assemblies Rinse Arm Pipe Cross Tube Inside TUB View Rear View Miscellaneous Electrical Diagram Specifications of the JPX-160 Dimensions of the JPX-160 JPX-160 Front View PCB Front and Bottom View Nut, Thermal Switch Back Panel Wash ARM/RINSE ARM Assemblies Blank, Wash Jet 01 02 03 04 05 06 07 Front View Bottom Right Side View JPX-160 Electrical Diagram Volt Circuit Components Diagram Specifications of the JPX-200 Dimensions of the JPX-200 Main Assembly TEM QTY Description Front and Bottom View Wash Element with Washers and Nuts Conduit Connector Fitting Left Hand Basket Ramp Indicates Item Not Shown Rinse Element Cover Electrical Diagram JPX-200 Components Diagram

jpx-140, JPX-160, JPX-200 specifications

The Jackson JPX series of paintball markers, encompassing the JPX-160, JPX-200, and JPX-140, is renowned for its innovative design and cutting-edge technology, catering to both amateur and professional players.

The JPX-160 stands out with its compact, lightweight design, making it highly maneuverable on the field. This marker employs the patented Jet Performance eXtraction (JPX) technology, which utilizes a unique propellant system that combines gas and paintballs for maximum velocity and accuracy. One of its main features is the adjustable velocity control, allowing players to customize the marker’s performance to match the competition's requirements. The JPX-160 also sports a quick-release magazine system that enables rapid reloads, vital in high-pressure situations.

Moving on to the JPX-200, this model enhances the features of the JPX-160, with a stronger body construction designed for durability and longevity. It introduces a dual-tube system, allowing for simultaneous shooting of different types of ammunition, including standard paintballs and rubber projectiles. The JPX-200 is equipped with an advanced ergonomic grip that reduces vibration, enhancing comfort during extended gameplay. Additionally, its integrated air chamber delivers consistent performance, ensuring players achieve optimal shots throughout the match.

Lastly, the JPX-140 is engineered with beginners in mind while still providing advanced features that seasoned players will appreciate. It integrates a simplified firing mechanism with a lightweight polymer construction, making it exceptionally easy to handle. This marker also has an adjustable sight for improved aiming and a reliable blowback system, offering a realistic shooting experience. The JPX-140 emphasizes ease of maintenance, equipped with user-friendly disassembly features that minimize downtime between games.

Together, the JPX series represents a versatile line of markers suitable for various play styles and skill levels. Their innovative technologies and user-centered designs ensure that players can enjoy an enhanced paintball experience, driven by performance, reliability, and comfort. Whether you are a competitive player looking for precision or a newcomer wanting to explore the sport, the Jackson JPX markers stand out as a solid choice. As paintball continues to evolve, the JPX series proves to be a valuable addition to any player's arsenal.
Top Page Image Contents