Instructions for Machine Transport

NOTE: Refrigerated equipment must remain upright to avoid damage to the compressor.

In order to prevent the oil contained in the compressor from flowing into the cooling system, it is necessary to always ship, carry, store and handle this drink dispenser in an upright position, fol- lowing the instructions located on the packaging. Never ship, carry, store or handle this unit on its side.

1.1 RECEIVING

Each unit is completely tested under operating conditions and thoroughly inspected before shipment. At the time of shipment, the carrier is responsible for the unit and any claim for dam- age must be made with the carrier. Upon receiving units from the delivering carrier, carefully in- spect the carton for visible indication(s) of damage. If damage exists, have carrier note same on bill of lading and file a claim with the carrier.

1.2UNPACKING

A.Cut band and remove.

B.Carefully remove top portion of carton by lifting up, see figure 1.

C.Remove top inner carton pad from inside of packing box.

D.Inspect unit for concealed damage and if evident, notify delivering carrier and file a claim against same.

Installation Positioning the machine

The machine must be well ventilated. Leave an 8” (20 cm) clearance on the sides and back of the machine to allow proper ventilation. Installation of the machine near a heat source should be avoided. Some heat sources you should avoid locating this unit too close to are ovens, coffee machines, cold or frozen beverage dispensers or ice machines (equipment with compressors that expel hot air through its vents). A room temperature between 59°F (15°C) and 77°F (25°C) is recommended.

Connection to Main Power Supply

•The electrical safety of this drink dispenser can only be achieved if the machine is properly connected to an appropriate grounded receptacle that is in compliance with current national safety standards. Therefore, the manufacturer cannot be held responsible for damage and/or injury caused by failure to connect the unit to an appropriate source of power.

•For a safe and correct installation, connect the unit to a dedicated outlet.

•Do not alter the cord or plug in any way.

•The entire length of the power supply cord must not, in any way, be compressed, bent, or bunched together, nor may extension cords be used.

•Do not obstruct the ventilation vents on the side and rear panels of the unit. Insufficient venti- lation will reduce the efficiency of the machine, causing it to function inadequately, and can cause serious damage. A minimum of eight inches (20cm) clearance is necessary on each side and behind the unit.

WARNING: THIS UNIT MUST BE PROPERLY ELECTRICALLY GROUNDED TO AVOID POSSIBLE FATAL ELECTRICAL SHOCK OR SERIOUS INJURY TO THE OPERATOR. THE POWER CORD IS PROVIDED WITH A THREE PRONG GROUNDED PLUG. IF A THREE-HOLE GROUNDED ELECTRICAL OUTLET IS NOT AVAILABLE, USE AN APPROVED METHOD TO GROUND THE UNIT. DO NOT USE EXTENSION CORDS WITH THIS UNIT. DO NOT “GANG” TOGETHER WITH OTHER ELECTRICAL DEVICES ON THE SAME OUTLET.

OSD30, OSD10, OSD20 specifications

The Omega OSD series, comprising the OSD30, OSD20, and OSD10 models, represents a cutting-edge evolution in the world of oceanographic monitoring and data collection technology. Designed for professional use in harsh marine environments, these devices are revolutionizing how researchers and oceanographers collect vital data.

The OSD30 stands at the forefront, equipped with advanced sensors that provide precise measurements of temperature, salinity, and ocean currents. Its high-tech design ensures durability and resilience, with a robust frame that can withstand extreme pressures and corrosive seawater. The OSD30 offers a large data capacity and can operate for extended periods, making it ideal for long-term deployments in deep-water scenarios. It features integrated wireless communication capabilities, allowing users to receive real-time data and make informed decisions on-site.

The OSD20, while slightly less advanced than the OSD30, still boasts impressive features that cater to serious oceanographers. It maintains high accuracy in environmental monitoring, providing essential readings of key oceanographic parameters. The OSD20 is designed with user-friendliness in mind; its intuitive interface and straightforward data retrieval process make it accessible for researchers of all levels. Moreover, it can be easily integrated with existing oceanographic tools, enhancing its versatility in various research applications.

On the other hand, the OSD10 is tailored for training and educational purposes. Although it has fewer features compared to its high-end counterparts, it still delivers reliable data collection capabilities. Its lightweight design and portability make it an excellent choice for educational institutions and field programs, providing students with hands-on experience in oceanographic research.

All three models share common characteristics, such as energy efficiency and minimal maintenance requirements. They utilize state-of-the-art battery technology, ensuring long operational life and reducing the frequency of replacements. The ruggedized designs of the OSD series mean that they are capable of operating in a variety of conditions, including extreme temperatures and turbulent waters.

In conclusion, the Omega OSD series presents a comprehensive set of tools for oceanographic research, ranging from high-tech solutions like the OSD30 to more accessible models like the OSD10. With their diverse applications, they are invaluable assets for scientists and educators alike, contributing significantly to our understanding of marine environments.