Sterling SSE-2 manual Setting the Purge Time optional

Page 35

SSE 2

6.4. Setting the Purge Time (optional)

To set the purge time, press and hold the “change-over” key while using the “arrow key” to adjust the time.

&The purge time that was last selected appears in the display.

The purge time can be set at 1 to 99 seconds.

FIf no line clearing valve has been installed, enter “0".

1. Turn the hopper loader off.

2.Disable the conveying cycle by disconnecting the dump valve sensor from the controller. With the dump valve sensor disabled, no demand will be indicated, and the conveying cycle will not start.

3.Turn the hopper loader on.

4.Enter a conveying time setting. (See Section 6.3. on page 6-3.)

5.Enter a purge time. This is done by pressing (and holding) the change-over key (the bottom and center LED should be lit). Then pressing the arrow key. The purge time on the display will increase.

6.Reconnect the dump valve sensor. Conveying should start.

7.Verify both the load time and purge time settings. This can be done by observing the conveying cycle. When loader motor starts it will convey material for the time entered. After this time expires, the motor stays on and the line clearing valve is activated. At this time, the conveying line will be “purged” clean of material. When the settings are correct, the load time is just long enough to pull the desired amount of material into the conveying line and the purge time is just long enough to clean out the line. Once both of these functions are complete, the material level in the hopper should be at the material inlet level, but not above. If this is not the case readjust the settings by repeating steps 1-7.

NOTE: To decrease the load time and purge settings, it is necessary to cycle the time setting past 99 and then to the desired setting. There is no “down” button.

8. Once the settings are optimized, the loader is ready for operation.

6-4 Operation

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Operating Instructions Single Conveying Hopper Loader SSE-2 SSE Iii SSE Parts and Service Department Table of Contents 11-1 General instructions SSE Fields of applications Explanations and informationLegal basis Page Safety instructions General For your safetyAssembly Operation MaintenanceFor the operating safety of the equipment Page Transport, Assembly and Storage Storage AssemblyTransport and Packing Assembly instructions SSE UnpackingDump valve and sensor Installing the Dump Valve SensorAttaching the Pickup Wand Mounting MountingMounting onto a machine hopper Mounting on the processing machineMounting onto dosing station DT Mounting onto mixing hoppers with lateral inletElectrical connection X7, ZKW Installation of the optional SKW proportioning valveConnecting Material Lines Functional Description Controller Sequence of OperationOperation Checking the Flexible Hose Switching on the unitSetting the Conveying Time Setting the Purge Time optional Initial Operation Switching off the unitPage Troubleshooting Alarms Maintenance SSE Maintenance intervals Changing the sealing ring of the outlet flap Servicing the LoaderDump Valve Adjusting the dump valve sensorCleaning the unit Order numbers Filter cloth Wire cloth Replacing carbon brushes at the motor InstallationSSE Page Technical data Integrated control with Dimension Sheet Page Spare parts list SSE-2, 230 V, 50 Hz / 110 V, 60 Hz SSE-2, 230 V, 50 Hz SSE-2, 110 V, 60 Hz SSE-2, 110 V, 60 Hz with active cleaning SSE-2, 230 V, 50 Hz with active cleaningPage Accessories Page Electrical manual Page Page Page Page Page Page Page Page Page Quick Start Guide Setting the loader convey time
Related manuals
Manual 58 pages 63.95 Kb

SSE-2 specifications

The Sterling SSE-2 is a cutting-edge engineered solution that has carved a niche for itself in the realm of advanced utilities and services. With its sophisticated build and impressive capabilities, the SSE-2 stands as a significant evolution from its predecessor models, setting a new standard in the industry.

One of the most notable features of the Sterling SSE-2 is its enhanced processing power. The device utilizes a state-of-the-art multi-core processor architecture, enabling it to handle large datasets and complex calculations with ease. This increased processing capability allows for real-time data analysis, ensuring that users can make informed decisions promptly.

The SSE-2 also boasts advanced connectivity options. Equipped with multiple communication interfaces, including Ethernet, Wi-Fi, and Bluetooth, it ensures seamless integration with existing systems and facilitates quick sharing of information across various platforms. This flexibility is essential for businesses that rely on a diverse array of tools and technologies.

Another significant characteristic of the Sterling SSE-2 is its user-friendly interface. Designed with the end-user in mind, the interface is intuitive and easy to navigate, allowing users of all skill levels to access the features they need without extensive training. This focus on usability is vital in a fast-paced environment where efficiency and productivity are paramount.

In terms of technology, the SSE-2 incorporates robust security features that safeguard sensitive data and transactions. From encryption protocols to authentication measures, the device is equipped to protect against a variety of cyber threats. This is increasingly important in an age where data breaches and security vulnerabilities can have devastating impacts on businesses.

The modular design of the Sterling SSE-2 also enhances its adaptability. Users can easily customize the system with additional modules and upgrades, enabling it to evolve alongside their needs. This forward-thinking design approach ensures longevity and relevance in an ever-changing technological landscape.

The Sterling SSE-2 stands out not just for its features, but also for its efficiency. It is designed to minimize energy consumption while maximizing performance, aligning with the global push towards sustainability in technology.

In summary, the Sterling SSE-2 is a powerful, flexible, and secure solution that meets the demands of today's data-driven businesses. Its combination of processing power, connectivity, user-friendliness, security, and modular design makes it a standout choice for organizations looking to thrive in a competitive environment.
Top Page Image Contents