Maytag W10175446B manual Refrigerator Doors and Drawer, Style 2-French Doors

Page 6

Refrigerator Door(s) and Drawer

TOOLS NEEDED: ⁵⁄₁₆", ³⁄₈", ¹⁄₄" hex-head socket wrench, a #2 Phillips screwdriver, and a flat-blade screwdriver.

IMPORTANT:

■Your refrigerator may have a standard reversible refrigerator door (Style 1) with either a freezer door or freezer drawer, or French doors (Style 2). Follow the instructions specific to the door style of your model.

■All graphics referenced in the following instructions are included later in this section after “Final Steps.” The graphics shown for the standard door (Style 1) are for a right-hand swing refrigerator (hinges factory installed on the right).

■If you only want to remove and replace the doors, see “Remove Doors and Hinges” and “Replace Doors and Hinges.”

■Before you begin, turn the refrigerator control OFF, and remove food and adjustable door or utility bins from the doors.

Remove and Replace Refrigerator Door Handles

Style 1–Standard Door

Front Mount Handle

■To remove the handle, remove the screw attaching the trim to the upper end of the handle. Using a flat-blade screw driver wrapped in masking tape, pry the trim piece from the lower end of the handle. Then, remove the screws attaching the handle to the door. See Front Mount graphic 2.

■To replace handle, reverse directions.

Side Mount Handle

■To remove the handle, remove the four screws attaching the handle to the side of the door. See Side Mount graphic 2.

■To replace the handle, align the holes in the handle with the holes in the door. Then, insert a screw in the upper hole at each end of the handle. Next, insert a screw in the lower holes. Tighten the screws. See Side Mount graphic 2.

Style 2–French Doors

Metal Handles

■Using a ³⁄₃₂" Allen wrench, loosen the two set screws located on the side of each handle. Pull the handle straight out from the door. Make sure you keep the screws for reattaching the handles. See Metal Handle graphic 1.

■To replace the handles, reverse the directions.

Plastic Handles

■To remove the handle, grasp the lower part of the handle firmly, slide the handle up and pull the handle straight out from the door. See Plastic Handle graphic 1.

■To replace the handle, position the handle so that the large holes in the mounting clips are down and align the holes with the door studs. Rotate the handle so that the mounting clips are flat against the door and slide the handle down to engage. See Plastic Handle graphic 1.

Remove Door and Hinges

Style 1–Standard Door

⁵⁄₁₆" Hex-Head Top Hinge Screw

Freezer drawer models

1.Unplug refrigerator or disconnect power.

2.Keep the refrigerator door closed until you are ready to lift it free from the cabinet.

NOTE: Provide additional support for the door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

3.Remove the parts for the top hinge as shown in Top Hinge graphic. Lift the refrigerator door free from the cabinet.

4.Remove the parts for the bottom hinge as shown in Bottom Hinge graphic.

Freezer door models

1.Unplug refrigerator or disconnect power.

2.Keep the freezer door closed until you are ready to lift it free from the cabinet.

NOTE: Provide additional support for the door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

3.Remove the parts for the top hinge as shown in Top Hinge graphic. Lift the refrigerator door free from the cabinet.

4.Remove the center hinge pin and remove the hinge screws as shown in the Center Hinge graphic. Lift the freezer door free from the cabinet.

5.Remove the parts for the bottom hinge as shown in Bottom Hinge graphic.

Style 2–French Doors

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

1.Unplug refrigerator or disconnect power.

2.Keep the refrigerator doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the refrigerator door while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Page Unpack the Refrigerator Installation InstructionsClean Before Using Before You Throw Away Your Old Refrigerator or FreezerLocation Requirements Electrical RequirementsRecommended Grounding Method Water Pressure Water Supply RequirementsConnect the Water Supply Reverse Osmosis Water SupplyComplete the Installation Connect to RefrigeratorStyle Refrigerator Doors and Drawer Style 2-French DoorsRemove Door and Hinges Style 1-Standard Door Cabinet Reverse Door Standard Door optionalReplace Door and Hinges Style 1-Standard Door Refrigerator doorRemove Drawer Front Remove and Replace Freezer DrawerRemove and Replace Drawer Handle Replace Drawer FrontDoor Removal Replacement Door Swing Reversal optional Style 1-Standard DoorDrawer Front Removal Drawer Front Replacement Adjust the Door Style1-Two Adjustable RollersStyle 2-Four Adjustable Rollers Opening and Closing Doors Using the ControlsRefrigerator USE Electronic and Dial ControlsDigital Controls Page Page Refrigerator Care CleaningTo Clean Your Refrigerator Changing the Light BulbTroubleshooting Refrigerator OperationTemperature and Moisture Ice and WaterWater is leaking from the dispenser system Water Filter CertificationsWater dispenser will not operate properly Water from the dispenser is warmPage Items Excluded from Warranty Maytag Major Appliance WarrantyLimited Warranty This limited warranty does not coverInstructions Dutilisation DU Réfrigérateur Sécurité DU RéfrigérateurInstructions D’INSTALLATION Exigences demplacementDéballage du réfrigérateur Spécifications de l’alimentation en eau Méthode recommandée de mise à la terreSpécifications électriques Pression de leauRaccordement de la canalisation deau Raccordement à une canalisation d’eauRaccordement au réfrigérateur Achever l’installation Portes et tiroir du réfrigérateurStyle 2-Porte à deux battants Modèles avec tiroir de congélation Dépose des portes et des charnières Style 1-Porte standardPoignées en plastique Modèles de compartiments de congélation avec portePorte du compartiment de réfrigération Réinstallation Porte et charnières Style 1-Porte standardCaisse Porte du compartiment de congélationRéinstallation de la façade du tiroir Retirer et réinstaller le tiroir du congélateurDépose et réinstallation de la poignée du tiroir Style 2-Portes à deux battantsInversion du sens douverture de la porte facultatif Style 1-Porte standardCharnières supérieures Style 2-Portes à deux battantsAjustement de la porte Style 1-Deux roulettes ajustablesStyle 2-Quatre roulettes ajustables Ouverture et fermeture des portes Utilisation des commandesUtilisation DU Réfrigérateur Style 3-Vis de réglage de laplombCommandes numériques Reset Filter réinitialisation du filtre Temp Alarm alarme de dépassement de températureDoor Alarm avertisseur de la porte Fast Ice glaçons rapidesPage Page Remplacement de l’ampoule d’éclairage Nettoyage de votre réfrigérateurDépannage Fonctionnement du réfrigérateurTempérature et humidité Glaçons et eauLe distributeur deau ne fonctionne pas correctement Leau du distributeur est tièdePage Garantie Limitée Articles Exclus DE LA GarantieLa présente garantie limitée ne couvre pas

W10175446B specifications

The Maytag W10175446B is a highly regarded appliance component widely used in the brand's range of refrigerators, particularly noted for its innovative technology and user-friendly features. This part, often associated with refrigerator water filtration systems, is designed to enhance the quality of drinking water and ice while ensuring that the appliance operates at optimal efficiency.

One of the primary characteristics of the W10175446B is its advanced filtration system. It is engineered to reduce contaminants such as lead, chlorine, and various sediment particles that can compromise the purity and taste of water. By utilizing activated carbon and other filtration media, the W10175446B effectively delivers clean, crisp water ideal for drinking and cooking.

Another significant feature of this component is its easy installation process. Designed for a seamless fit in compatible Maytag refrigerator models, the W10175446B allows homeowners to replace their filters without the need for specialized tools or professional assistance. This accessibility is a notable advantage for consumers who prioritize DIY maintenance and convenience.

In terms of performance, the W10175446B showcases exceptional flow rates, ensuring that water dispensed from the refrigerator remains consistent in pressure and taste. This ensures that ice and drinking water are always readily available, making it perfect for busy households that rely heavily on their refrigerator's water and ice dispensers.

The longevity of the W10175446B is another appealing aspect. This part typically has a lifespan of six months, depending on usage and water quality. This regular replacement cycle encourages homeowners to stay proactive about their water quality, ensuring that they enjoy fresh and safe drinking water year-round.

Moreover, the W10175446B is designed with environmental considerations in mind. The filtration system reduces the need for bottled water, helping to decrease plastic waste and promote sustainable practices. It's a small but significant step towards more eco-friendly living.

Overall, the Maytag W10175446B is an essential part for elevating the functionality of Maytag refrigerators. With its advanced purification technology, ease of use, reliable performance, and eco-conscious design, it stands out as a valuable component that enhances both family health and appliance efficiency. Choosing the W10175446B means choosing quality, convenience, and sustainability.
Top Page Image Contents