Toshiba RD-X2U To delay the end time while recording, Entering the recording format on the DVD-R

To delay the end time while recording

Press the EXTEND button under the lid of the remote control.

When you press it once, the current end time appears. Each time you press the button, the end time (displayed in the indication section) is delayed in 10 minutes increments, up to 60 minutes.

Notes

•Pressing any button other than the EXTEND button completes this procedure to determine the end time.

•This operation must be performed prior to 1 minute before the programmed end time.

•A recording automatically finishes when the disc is full or when the recording exceeds 9 hours regardless of whether or not you delayed the end time.

To play a title recorded on the HDD while recording on the HDD (Recorded Title Play in

HDD) HDD

This function works only during HDD recording.

You cannot play a title recorded on a DVD-RAM disc sinultoneously with DVD-RAM recording.

1)While recording on the HDD, press the CONTENT MENU button.

2)Press the / / / buttons to select a desired title, then press the ENTER button.

Playback of the selected title starts.

Pressing the STOP button stops playback, and the content that is being recorded appears on the display. If you press the PLAY button, playback resumes from the location you last stopped.

Note

•While you are using this function, the following operations/ functions are not available.

-Dividing chapters. (By the CHP DIVIDE button)

-Programmed playback (Repeat playback, etc.)

-Editing (Chapter dividing, Playlist programming, dubbing, title naming, title thumbnail setting, intro scan)

•While performing relay recording ( page 70), this function is not available.

Entering the recording format on the DVD-R

Before recording, make sure “DVD-R Broadcast Record” is set to “Main” or “SAP” ( page 128).

Notes

•You cannot close the disc tray automatically at the recording start time. If you want to record on a DVD-RAM disc, load it on the recorder beforehand.

•While recording, you cannot change the settings of a program, such as the channel, mode, etc.

•The number of titles cannot exceed in any case 99 for a DVD-RAM and 198 for the HDD.

•You cannot record on both an HDD and a DVD-RAM disc at the same time (except relay recording).

•The maximum length of a recording is 9 hours. Recording automatically stops when length exceeds 9 hours.

•While performing a programmed recording, you cannot program a new timer selection.

•You may not be able to start recording if there is too little time before a programmed recording begins.

•A programmed recording may not be executed if a power failure occurrs within 5 minutes before the start time.

•If an HDD starts programmed recording while you are playing a DVD-drive disc, the picture may pause momentarily.

•When you record monaural sound, the same sound is recorded to both left and right channel.

•When you record a bilingual program in the “L-PCM” mode ( page 35), the sound is recorded as stereo. In this case, both the main and sub sound will be output at the same time. Select the output sound by pressing the INPUT SELECT button.

•When you record content which will be dubbed on a DVD-

R, be sure to set “DVD-R Broadcast Record” to “Main” or “SAP” ( page 128).

•To select SAP, set “SAP” to “on” ( page 124).

•When you set “DVD-R Broadcast Record” to “Main” or “SAP” ( page 128), only the selected sound of the bilingual program (main or sub) is recorded.

•When you set “DVD-R Broadcast Record” to “Main” or “SAP” ( page 128), only the selected sound of the bilingual program is recorded. To prevent this, set “DVD-R Broadcast Record” only when you record content that will be dubbed to a DVD-R.

Introduction Basic operations Playback Recording

Dubbing

Editing Function setup Others

39

*RD-X2.Ope(US)p027-044 39 9/3/02, 11:23 AM