GE JGRP20 Oven Light Replacement, Removable Oven Bottom, To replace cover, Self-clean cycle

Page 26

Care and cleaning of the oven.

Safety Instructions

Instructions

Wire cover holder

Oven Light Replacement

CAUTION: Before replacing your oven light bulb, disconnect the electrical power to the oven at the main fuse or circuit breaker panel. Be sure to let the light cover and bulb cool completely.

The oven light bulb is covered with a removable glass cover that is held in place with a bail-shaped wire. Remove the oven door, if desired, to reach the cover easily.

To remove:

Hold a hand under the cover so it doesn’t fall when released. With fingers of the same hand, firmly push back the wire cover holder. Lift off the cover.

Do not remove any screws to remove the cover.

Do not touch hot bulb with a wet cloth. Replace bulb with a 40-watt household appliance bulb.

To replace cover:

Place it into the groove of the light receptacle. Pull the wire forward to the center of the cover until it snaps into place. When in place, the wire holds the cover firmly. Be certain the wire is in the depression in the center of the cover.

Connect electrical power to the oven.

Operating

Troubleshooting Tips

 

 

Removable Oven Bottom

 

 

The oven bottom can be removed to clean large

 

 

spills, and to enable you to reach the oven burner.

Unlock

Lock

Oven bottom must be replaced before using

the self-clean cycle.

 

 

To remove:

 

 

Slide the tab at the center front of

 

 

the oven bottom to the left.

 

 

Lift the oven bottom up and out.

 

 

To replace:

 

 

Slip the oven bottom into the oven

 

 

so the tabs in the rear of the oven

 

 

bottom fit into the slots in the

 

 

oven back.

 

 

Lower the front of the oven bottom

 

 

into place and slide the front tab to

 

 

the right to lock the oven bottom

 

 

into place.

The oven bottom has a porcelain enamel finish. To make cleaning easier, protect the oven bottom from excessive spillovers by placing a cookie sheet on the shelf below the shelf you are cooking on. This is particularly important when baking a fruit pie or other foods with a high acid content. Hot fruit fillings or other foods that are highly acidic (such as tomatoes, sauerkraut, and sauces with vinegar or lemon juice) may cause pitting and damage to the porcelain enamel surface and should be wiped up immediately.

We don’t recommend using aluminum foil on the oven bottom. It can affect air flow if the holes are blocked and it can concentrate heat at the bottom of the oven, resulting in poor baking performance.

To clean up spillovers, use soap and water, an abrasive cleaner or soap-filled scouring pad. Rinse well to remove any soap before self-cleaning.

Consumer Support

Oven Shelves

Clean the shelves with an abrasive cleanser or scouring pad. After cleaning, rinse the shelves with clean water and dry with

a clean cloth.

NOTE: Take the shelves out of the oven before you begin the self-clean cycle.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Built-In Gas Write the model and serial numbers here Model # Serial #What to do if YOU Smell GAS Important Safety Notice Cook Meat and Poultry THOROUGHLY… Oven SELF-CLEANING Oven Using the oven controls Oven Control, Clock and Timer Features and SettingsUsing the clock and timer Power Failure Tones While Setting the Control Preheat Notification ToneHour Shut-Off Special features of your oven controlTones at the End of a Timed Cycle Cook and HoldControl Lockout Fahrenheit or Centigrade Temperature SelectionHour, 24-Hour or Clock Black-Out Changing the Speed of the +/- PadsUsing the oven Oven Shelves Shelf PositionsOven Moisture Oven Shelves Using the baking featureHow to Set Your Oven for Baking PreheatingPies Baking PansCookies CakesUsing the timed baking feature How to Set Immediate Start and Automatic StopHow to Set Delay Start and Automatic Stop Type of margarine will affect baking performance Adjust the oven thermostat-Do it yourselfTo Adjust the Thermostat Before You Begin Roasting… Using the roasting featureHow to Set Your Oven for Roasting Questions and Answers Why is my roast crumbling when I try to carve it?Before You Begin Broiling… Using the broiling featureHow to Set Your Oven for Broiling Use of Aluminum FoilBroiling Guide Usda Rev. JuneHow to Set the Oven for Cleaning Using the self-cleaning ovenBefore a Clean Cycle SafetyAfter a Clean Cycle Should there be any odor during the cleaning?Broiler Pan and Grid Care and cleaning of the ovenHow to Remove Packaging Tape Removable Storage DrawerRemovable Oven Bottom Oven Light ReplacementSelf-clean cycle Do not remove any screws to remove the coverControl Panel To clean the inside of the doorTo clean the outside of the door Lift-Off Oven DoorAdjusting Orifice Hoods Broil and Oven Burner Air Adjustment ShuttersBefore you call for service… Clean cycle See the Using the self-cleaning oven sectionAfter a clean cycle Oven not clean after a Crackling orDisplay goes blank Power outageCall for service On outer cones Display flashesPage We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration What GE Will Not Cover GE Gas Oven WarrantyGE Will Replace, At No Charge To You Operating InstructionsConsumer Support GE Appliances Website Schedule ServiceParts and Accessories Real Life Design Studio
Related manuals
Manual 36 pages 38.22 Kb

JGRP20 specifications

The GE JGRP20 is a prominent jet engine widely used in modern aviation, recognized for its efficiency, power, and advanced engineering. Developed by General Electric, this engine serves as a key component in various commercial and military aircraft, offering a blend of performance and reliability that meets the demands of today's dynamic air transport sector.

One of the primary features of the JGRP20 is its advanced turbofan design, which allows for improved fuel efficiency and lower emissions compared to older engine models. The engine incorporates cutting-edge materials such as advanced composites and titanium alloys, which contribute to its lightweight structure while ensuring durability and longevity. This makes the JGRP20 an environmentally friendly choice, aligning with global efforts to reduce the carbon footprint of aviation.

The engine boasts a high bypass ratio, which enhances its thrust capabilities while operating at lower noise levels. This is particularly advantageous for urban airports where noise regulations are stringent. The combination of high bypass ratio and advanced aerodynamics enables the JGRP20 to deliver superior performance during takeoff and cruising phases of flight.

Advanced technologies integrated into the GE JGRP20 include digital engine control systems, which optimize performance and efficiency throughout the flight. With real-time monitoring and data analysis, the engine can adapt to varying flight conditions, ensuring optimal fuel consumption and thrust. Furthermore, the engine's component health monitoring system provides invaluable insights into the operational status, allowing for predictive maintenance and minimizing downtime.

In terms of operational versatility, the JGRP20 can be tailored to suit a range of aircraft configurations, making it a flexible solution for airlines and military operators alike. Its capacity for various thrust settings allows it to power a wide array of aircraft from regional jets to larger commercial airliners.

In summary, the GE JGRP20 represents the pinnacle of jet engine design and technology. With its commitment to efficiency, reduced emissions, and noise reduction, alongside its robustness and adaptability, it stands as a trusted choice for aviation stakeholders seeking reliable and high-performing engines for their fleets. This engine not only exemplifies GE's engineering prowess but also highlights the industry's ongoing evolution towards more sustainable air travel practices.
Top Page Image Contents