GE ZBD6605 ZBD6905 ZBD7005 ZBD7105 Control Panel/Operation ZBD6905, Normal, High, Sani

Start a wash load

Control Panel/Operation – ZBD6905

Chef’s Washer

3.SMART DRY–When selected, sensors detect the presence of rinse aid and the final rinse temperature. The drying heater and fan are then turned on for the minimum time to achieve optimum drying results, saving energy over conventional heated dry and time over non-heated dry. SMART DRY is not available on RINSE ONLY.

4.WATER TEMP–This button provides extra heat options to increase water temperature for optimum performance.

NORMAL	This is the default setting–provides a wash and rinse with water temperatures
	up to 125°F (51°C) in the LIGHT WASH, 135°F (57°C) in the NORMAL
	WASH cycle and 155°F (68°C) in HEAVY DUTY.
HIGH	This water temp selection provides a wash and rinse with water temperatures
	up to 160°F (71°C) in LIGHT WASH, NORMAL WASH and HEAVY DUTY.
	Use this option for heavily soiled dishes. Cannot be used with RINSE ONLY.
SANI	This water temp selection provides a sanitizing wash and rinse with water
	temperatures up to 160°F (71°C) in LIGHT WASH and 171°F (77°C) in
	NORMAL WASH and HEAVY DUTY. Cannot be used with RINSE ONLY.
	At the end of the WASH cycle, the SANI OPTION light will remain illuminated
	to indicate that the sanitization conditions have been met.

		S	ID E N	T	I	NSF INTERNATIONAL
	E					Meets NSF Protocol for Performance of Domestic Spray-Type Pots
					A
R					L
						and Pans Washing Machines (NSF Protocol P180) Requirements
						for cleaning and sanitization of cookware.

5.DELAY START–This option will allow you to delay the start time of any wash cycle except RINSE ONLY for up to 6 hours.

1.Select the delay start time you want by pressing the DELAY START button. Multiple pressing will alternate the delay time between 2, 4 or 6 hours and OFF.

2.The last programmed cycle will automatically be selected. A new cycle and options can also be selected. The DELAY START light/lights will flash to indicate time selected.

3.The flashing Delay Start Indicators show how many hours will elapse before washing begins.

To start the Chef’s Washer, close the door until it locks in place. The last used cycle will be displayed. To begin this cycle, push the START button. To select a different cycle, push the desired Cycle Selection and Option buttons, and then press the START button.

The door must be closed and latched into place to select a cycle or an option.

To interrupt/pause a cycle, press the selected cycle button. The Status Indicators will flash.

CAUTION: Be careful when opening the door; the hot steam that escapes when the door is opened may cause injuries. Stand back as you open the door and allow the steam to escape.

ATTENTION : Faites attention lorsque vous ouvrez la porte. La vapeur brûlante qui s’échappe lorsque vous ouvrez la porte pendant un programme de lavage peut causer des brûlures. Lorsque vous ouvrez la porte, reculez et laissez la vapeur s’échapper de l’appareil.

To restart the wash process, close the door until it locks in place. Re-press the cycle button. There may be a time delay of up to a few minutes, because the temperature inside the Chef’s Washer needs to stabilize before it restarts the wash cycle. During this time the SENSING light will be on.

To cancel the cycle after it has started, press and hold the START/CANCEL button for 3 seconds. The Chef’s Washer will then drain and the cycle indicator lights will flash. At this point a new wash cycle can be selected. If a new cycle is not selected, all the Cycle Indicator lights will go out after the Chef’s Washer drains. If you have selected a new wash cycle, remember to add more detergent to the detergent compartment if required.

11