Operating Instructions, Troubleshooting Tips

Safety Instructions

Operating Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING —

SAVE THESE INSTRUCTIONS

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, and to prevent property damage, personal injury, or death.

WARNING! WATER HEATER SAFETY

Under certain conditions hydrogen gas may be produced in a water heater that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE.

If the hot water has not been used for two weeks or more, prevent the possibility of damage or injury by turning on all hot water faucets and allow them to run for several minutes. Do this before using any electrical appliance which is connected to the hot water system. This simple procedure will allow any built- up hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or appliance during this process.

PROPER INSTALLATION AND MAINTENANCE

This dishwasher must be properly installed and located in accordance with the Installation Instructions before it is used. If you did not receive an Installation Instructions sheet with your dishwasher, you can receive one by visiting our website at ge.com.

Troubleshooting Tips

■Connect to a grounded metal, permanent wiring system; or run an equipment-grounding conductor with the circuit conductors and connect to the equipment-grounding terminal or lead of the appliance.

■Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded.

■Dispose of discarded appliances and shipping or packing material properly.

■Do not attempt to repair or replace any part of your dishwasher unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician.

■To minimize the possibility of electric shock, disconnect this appliance from the power supply before attempting any maintenance.

NOTE: Turning the dishwasher off does not disconnect the appliance from the power supply. We recommend having a qualified technician service your appliance.

CAUTION: To prevent minor injury or property damage

Consumer Support

■Contents washed in Anti-bacterial mode, if

available, may be hot to the touch. Use care before handling.

		■Using a detergent that is
		not specifically designed
		for dishwashers will cause
		the dishwasher to fill with
		suds.
		■If your dishwasher is connected to a
		wall switch, ensure that the switch is
		on prior to use.
		■On dishwashers with electronic controls,
		if you choose to turn the switch off
		between wash cycles, allow 5-10
		seconds after turning the switch on before
	2	touching START/RESET to allow the control to
	2	reboot.
		reboot.

■Non-Dishware Items: Do not wash items such as electronic air cleaner filters, furnace filters and paint brushes in your dishwasher. Damage to dishwasher and discoloration or staining of dishwasher may result.

■Close supervision is necessary if this appliance is used by or near children.

■Load light, plastic items so they will not become dislodged and drop to the bottom of the dishwasher—they might come into contact with the heating element and be damaged.

GLDL500 specifications

The GE GLDL500 is an innovative and advanced gas turbine engine designed for various applications, including power generation and industrial processes. Known for its efficiency, reliability, and advanced technology, the GLDL500 is a prime example of General Electric's commitment to producing cutting-edge energy solutions.

One of the main features of the GE GLDL500 is its high efficiency. The engine is designed to operate at an impressive thermal efficiency, allowing for lower fuel consumption and reduced emissions. This efficiency not only contributes to cost savings but also supports environmental sustainability efforts by minimizing the carbon footprint of operations.

The GLDL500 incorporates advanced materials and manufacturing techniques that enhance its performance and durability. It utilizes heat-resistant superalloys in its turbine section, which allow the engine to withstand the extreme temperatures and stresses experienced during operation. This not only prolongs the lifespan of the turbine but also improves the overall reliability of the system.

Another key characteristic of the GE GLDL500 is its modular design. This design enables easy maintenance and upgrades, making it a flexible choice for operators looking to adapt to changing energy demands or to incorporate new technologies. The modularity also simplifies logistics and reduces downtime, leading to increased operational efficiency.

The GLDL500 features advanced digital controls and monitoring systems. These systems provide real-time data on engine performance, allowing operators to make informed decisions and optimize the turbine's operation. The incorporation of digital technologies fosters predictive maintenance, helping to identify potential issues before they become significant problems.

In terms of environmental performance, the GE GLDL500 is compliant with stringent emission regulations. The engine is engineered to minimize NOx and CO2 emissions, ensuring that it meets or exceeds industry standards. This focus on clean energy solutions aligns with global efforts to transition towards more sustainable energy sources.

Overall, the GE GLDL500 stands out as a powerful, efficient, and environmentally friendly gas turbine engine. Its combination of advanced features, innovative technologies, and robust characteristics makes it an ideal choice for a variety of applications in the modern energy landscape, demonstrating GE's leadership in the gas turbine market. Operators investing in the GLDL500 can expect enhanced performance, reduced operational costs, and a commitment to sustainability.