Fisher & Paykel DD60S 7, DD60ST 7 installation instructions Final Checklist, Troubleshooting

Page 23

26FINAL CHECKLIST

Check all parts are installed.

Ensure that all panels and parts thereof are secure and final electrical tests have been conducted in accordance with local electrical regulations.

Ensure product is level, securely fastened to the cabinetry and opens and closes freely. The drawer must be free to fully close with no resistance from the cabinetry.

Ensure inlet hose to water supply has supplied rubber washer fitted, and that it’s tightened a further half turn after seal contact.

Ensure any knockouts or plugs in drain connection have been drilled out and drain connection has been made.

The drain hose joiner must not support the weight of excess hose material. Keep drain hose as fully extended as possible to prevent sagging. Any excess length of drain hose should be kept on the dishwasher side of the highloop.

If connecting the drain hose to the sink trap, ensure the Highloop is a minimum 150 mm higher than the drain hose joiner.

Ensure any packaging or tape securing the racks is removed from the drawer. Turn on the power and water supplies, then open the drawer. You should hear a beep and see a program indicator light up on the internal control panel.

Check the spray arm is in place and free to rotate.

Spray arm

Add three cups of water into the drawer. Press on the internal control panel until the indicator of the ‘Rinse’ program lights up. Close the drawer and press to start the program.

After the Rinse program has finished, ensure the dishwasher has run and drained correctly.

Check water supply and drainage connection for leakage.

27 TROUBLESHOOTING

23

 

Excessive water remaining above the filter plate, after the rinse cycle

Check for a kinked drain hose, blocked waste connection, highloop not properly installed, drain hose not routed correctly or spray arm not in place.

No water supply (This is displayed as a ‘U1’ fault -- see section ‘If there is a fault’ in the User guide for how to recognise this fault on models without a display.)

Check water is connected and turned on.

The dishwasher is beeping continuously

There is a fault. See section ‘If there is a fault’ in the User guide for further information and instructions.

No program indicator lights up when the drawer is opened

Ensure power is connected and is switched on. If it is and still no indicator ligths up, see the ‘Preference options’ section of the ‘Quick start guide’. An option called ‘Open drawer auto power-on’ may need to be turned on.

Water around water supply and drainage connections

Check connections, existing plumbing and hoses for leaks. Check rubber washer and hose clamp are correctly fitted.

If product is tipping

Ensure the product is secured to the cabinetry.

If front panels are misaligned

Check and relevel product. Check the cabinetry is square. For Integrated models, check and adjust front panel alignment if necessary.

Drawer doesn’t close properly

Ensure nothing is obstructing the drawer from closing properly eg sound insulation, hoses or drawer latches.

If a problem occurs, consult the ‘Troubleshooting’ section of the User guide. If after checking these points you still need assistance, please refer to the Service & Warranty book for warranty details and your nearest Authorised Service Centre, or contact us through our website, listed below.

Important!

SAVE THESE INSTRUCTIONS

The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit our local website listed at the end of this document or contact your local Fisher & Paykel dealer.

www.fisherpaykel.co.nz www.fisherpaykel.com.au www.fisherpaykel.co.uk www.fisherpaykel.ie www.fisherpaykel.eu

Image 23
Contents Installation Instructions Standard Height Single Models Follow the Installation Sequence Relevant to Your Model2b Additional Safety and Warnings Integrated Models only 2a Safety and Warnings ALL ModelsOptional 3a Parts Supplied ALL ModelsWith badge GB IE only 3b Additional Parts Supplied with Integrated ModelsSupplied with Integrated models with remote NZ AU only Product dimensions mm Product DimensionsMinimum clearances from adjacent cabinetry Cabinetry DimensionsFront Panel Specifications Min mm ventilation gap Moisture 10 mm protection Tape must be applied 7a Cavity PreparationShelf cutouts Venting hose 1525 mm Maximum Distance of Hoses & Cord from Chassis EdgeDrain hose 2000 mm Inlet hose 1650 mmTabs and it clicks into place 10a Attach Side Mounting Brackets NOW Choose Which Installation Method a or bFour brackets Repeat for all11b Pull Through Hoses & Move Into the Cavity 10b Integrated Models with Remote NZ AU onlyProduct has three pairs of fixing points 14b Refit the Drawer Onto the Runners15b Integrated Models with Remote NZ AU only 18a Earth the Panel 19a Attach Panel to Product 20a Adjust Panel Height to Align the Cabinetry Gaps 19b Attach Panel to Panel Bracket 18b Route Badge Wiring Through PanelPlace 22b Adjust Panel Height to Align the Cabinetry GapsPlug Product Connect Inlet Hose to Cold WaterTroubleshooting Final Checklist

DD60S 7, DD60ST 7 specifications

Fisher & Paykel has established itself as a leader in the world of kitchen appliances, and their range of dishwashers is no exception. Among their standout models are the DD60ST7 and DD60S7, both designed to deliver exceptional cleaning performance while seamlessly integrating into modern kitchens.

The Fisher & Paykel DD60ST7 is a slimline dishwasher that provides efficient cleaning for those who require a compact solution. With a width of just 60 cm, it is perfect for smaller spaces without sacrificing capacity. This model can accommodate up to 15 place settings, offering flexibility for both everyday meals and large gatherings. Its elegant design features a stainless-steel front that not only looks sophisticated but is also easy to clean.

On the other hand, the DD60S7 is a full-sized dishwasher designed for larger households. With an impressive capacity of 16 place settings and multiple wash programs, it caters to a variety of cleaning needs. This model also boasts a flexible racking system, allowing users to customize the interior layout to fit large pots, pans, and delicate glassware.

Both dishwashers are equipped with SmartDrive technology, which utilizes a brushless DC motor that adjusts to the load size and soil level. This innovation provides efficient water and energy use, making the machines eco-friendly choices. Additionally, these models feature a variety of wash programs, including a quick wash option for those times when you need clean dishes in a hurry.

Another notable feature is the quiet operation of these dishwashers. With a low decibel rating, they run quietly in the background, allowing you to carry on with your daily activities without disruption. The dishwashers also include a unique DryPlus feature, which enhances drying performance through increased heat and time, ensuring that your dishes come out spotless and dry.

For those who value convenience, both models include a delay start function, allowing users to load the dishwasher and set it to run at a later time. This can be particularly helpful for optimizing energy use during off-peak hours or for running the dishwasher overnight.

In summary, Fisher & Paykel's DD60ST7 and DD60S7 offer modern kitchen solutions with their compact and full-sized options, respectively. With efficient cleaning technologies, flexible racking systems, and whisper-quiet operation, they stand out as formidable contenders in the dishwasher market, providing both style and functionality for today's discerning homeowners.