GE Numbers 2 Defrost Water I%, Light Bulb Replacement, When YouMove, When You Goon Vacation

Page 19

Defrost Water I%

Pan behind base grille should be cleaned at least once a year. When reinstalling pan, firmly push it ALL THE WAYIN until it stops.

I ~

\

~’ /

 

Defrost water pan

Light Bulb Replacement

In Fresh Food Compartment

1.Unplug refrigerator.

2.Thm numbered temperature control to OFF and pull off knob.

~Grooved

fl#iaih-

In Freezer Compartment

1.Unplug refrigerator.

I

II

2.Remove-shelfjust below light shield. (Shelf will be easier to removeif it is emptied first.)

3.Pull plastic light shield toward you. (It will bend to free tabs from grooves. )

After replacing with same size bulb, reinstall shield and shelf and plug refrigerator back in.

In Refreshment Center

1. Unplug refrigerator.

2.Open fresh food compartment

door, remove top Rxta-Bin and raise Refreshment Center inner door.

tablespoon of soda to one quart of water. Wipe dry. To prevent odors.

leave open box of soda in refrigerator. Leave doors open.

For shorter vacations, remove perishable foods and leave controls at regular settings. However, if room temperature is expected to drop below 60”F., follow same instructions as for extended vacations.

Move icemaker feeler arm to OFF (up) position and be sure to shut off water supply to the refrigerator.

When YouMove

Disconnect power cord from wall outlet, remove all food and clean and dry the interior.

Secure all loose items such as grille, shelves and storage pans by taping them securely in place to prevent damage.

Be sure refrigerator stays in upright posi?ion only during actual moving and in van. Refrigerator must be secured in van to prevent movement. Protect outside of refrigerator with blanket.

3.Pull bottom of light panel down about 1/4“-just enough to disengage lip at rear from grooves in retainers on rear wall.

4.Lift panel to disengage top from pins on sidewalls; remove panel.

After replacing with same size bulb, reinstall panel (hang top on

pins; pull bottomdown, push it back and release it to let lip engage grooves in retainers). Replace temperaturecontrol knob in OFF position, turnit to previous setting, and plug refrigeratorback in.

I

I ’11

3.Press sides of flexible light shield to release locking tabs and allow the shield to swing down.

4.Unscrew burned-out bulb and replace it with night-light bulb of same wattage.

5.Place rear tab of light shield into door and rotate shield up until tabs lock into slots above.

6.Plug refrigerator back in.

When You Goon Vacation

For extended vacations or absences, shut off power to refrigerator, turn the numbered control to OFF, clean interior w ith baking soda solution of one

19

-J l-l-

Water Filter Accessorv

w

The perfect companion to your automatic icemaker— a water filter

Your ice cubes can only be as fresh-tasting as the water that produces them. That’s why it’s a good idea to purify your water with a water filter.

Its activated charcoal removes musty, stale odors and unpleasant medicinal, metallic tastes. A porous fiber cartridge catches dirt, rust particles, sand and silt while special crystals reduce deposits of hard scale.

The water filter is an option at extra cost and is available from your GE dealer. Specify WR97X214. It has complete installation instructions and installs in minutes on 1/4” O. D. copper water line.

—-——

-–1—11———–--l-——

-– -– —––-–––-–-

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Temperature Controls Vacation & Moving Tips Light Bulb ReplacementProblem Solver 20-22 Repair Service Safety InstructionsRead this book carefully Help us Help youWrite down the model and serial numbers Installation Requirements -IMPORTANT Pease read carefully Read all instructions before using this applianceInstallation Requirements -RT~T Operating Your Refrigerator Above normal Electronic Monitor & Diagnostic SystemWhen your refrigerator Is first plugged @Flashing green diagnostic codes in the display warn youWhy the Red Warm Temperature Light Glows How to Set Door AlarmHow the Electronic Monitor and Diagnostic System Works Check temperature controls Electronic Monitor Diagnostic System alerts you whenCheck your frozen food. Has any Signal Lights Diagnostic Codes Refreshment Center Compartment Refreshment CenterIcemaker Ice & Water DispenserImportant Facts about YourIce & WaterDispenser Before Using Your Icemaker and DispenserIce & Chilled Water Dispenser Automatic Icemaker and Ice & Water DispenserTo Dispense Ice and Water When Dispensing IceWhen Dispensing Water Once Your Icemaker Dqenser Are in OperationIf Ice Clumps Form Storage Bin To Stop DispensingTo Remove Ice Cube Storage Bin FrequentlyFor Convenience Fwd Storage SuggestionsSuggested Storage Times Tips on Freezing FoodsCool ‘n Fresh Drawer Variable temperature controi regulatesthe air tlow fromGeneral Electric Food-SaverSystem Moist ‘n IWeshDrawerQuick Serve System Sealed Snack@~e Drawers Shelf Positions Behind Refrigerator Care and CleaningCleaning-Outside Cleaning-InsideWater Filter Accessorv Light Bulb ReplacementWhen YouMove When You Goon VacationRapid Electrical Diagnosis Questions? MUse This Problem Solver~r q tie &n left aj~ or pac@e holding door open No power at outlet Light bulb needs replacing. See Problem SolverIf YouNeed Service Warranty

Numbers 2 specifications

The GE Numbers 2 represents a significant leap in advanced technology and engineering design, showcasing General Electric's commitment to innovation. This cutting-edge machine is engineered to meet the ever-evolving demands of various industries, including energy, transportation, and manufacturing.

One of the standout features of GE Numbers 2 is its high efficiency. The system is designed to optimize performance while reducing energy consumption, which is essential in today’s cost-sensitive environment. This efficiency is achieved through advanced predictive analytics that monitor operational performance in real time, allowing for immediate adjustments to maintain optimal conditions.

Moreover, the GE Numbers 2 incorporates state-of-the-art materials and engineered components, enhancing durability and reliability. The use of lightweight yet robust materials contributes to the overall performance while minimizing maintenance needs. This quality makes it particularly advantageous for harsh operating conditions, ensuring longevity and a lower total cost of ownership.

In terms of technology, GE Numbers 2 integrates the latest automation and control systems. It utilizes artificial intelligence and machine learning algorithms to analyze data collected from its various sensors. This data-driven approach enables proactive maintenance strategies, ultimately reducing downtime and enhancing productivity.

Connectivity is another critical feature of GE Numbers 2. With its advanced IoT capabilities, the machine can integrate seamlessly with existing infrastructure. This connectivity allows for remote monitoring and management, providing operators with the flexibility to oversee operations from anywhere.

The design of GE Numbers 2 focuses on user experience and accessibility. Its intuitive interface simplifies operation, enabling users to make quick adjustments and monitor performance metrics easily. This usability is coupled with extensive training resources and support, ensuring that operators can leverage the machine’s full potential.

Additionally, GE Numbers 2 places a strong emphasis on sustainability. The machine's design and operation focus on minimizing environmental impact, aligning with global efforts toward greener technology. This commitment to sustainability is not only good for the environment but also resonates with customers looking to enhance their corporate social responsibility profiles.

In summary, GE Numbers 2 is a testament to General Electric's innovative spirit, combining efficiency, advanced technology, and sustainability to deliver solutions that meet the needs of modern industries. Its robust features and intelligent connectivity make it a valuable asset for businesses aiming to excel in a competitive landscape.
Top Page Image Contents