Heater Kit Accessory Installation

Compressor

Units are shipped with compressor mountings factory- adjusted and ready for operation. Caution: Do not loosen compressor mounting bolts.

Heater Kit Accessory (if used)

The unit is fully equipped for cooling operation without auxiliary heat. A heater kit accessory may also be used.

To install the heater kit accessory (see Figure 7):

1.Disconnect the power and remove the heater compartment access panel.

2.Disconnect the plug separating the high voltage wire harness. Remove the high voltage wire harness plug and discard.

3.Remove the heater blockoff by removing the four screws holding it in place.

4.Insert the heater into the control panel and fasten in the same mounting holes.

5.Plug the heater wiring harness into the wire harness on the control assembly. Field wiring of the auxiliary heater is separate from the unit power supply. Wire the power supply wiring for the heater to the appropriate connections on the heater kit.

6.Replace the heater compartment access panel and reconnect the power.

Removal of Unit from Common Venting System

When an existing indoor furnace is removed from a common venting system serving other appliances, the venting system is likely to be too large to properly vent the remaining attached appliances. The following test should be conducted with each appliance while the other appliances connected to the common venting system are not in operation.

1.Seal any unused openings in the common venting system.

2.Visually inspect the venting system for proper size and horizontal pitch and determine there is no blockage or restriction, leakage, corrosion, or other deficiencies which could cause an unsafe condition.

Heater

Blockoff

Heater

Compartment

Access

Panel

Heater Kit

Figure 7

3.Insofar as is practical, close all building doors and windows between the space in which the appliances remaining connected to the common venting system are located and other spaces in the building. Turn on clothes dryers and any appliance not connected to the common venting system. Turn on exhaust fans, such as range hoods and bathroom exhausts, so they will operate at maximum speed. Do not operate a summer exhaust fan. Close fireplace dampers.

4.Following the lighting instructions, place the unit being inspected in operation. Adjust the thermostat so the appliance will operate continuously.

5.Test for spillage at the draft control relief opening after 5 minutes of main burner operation. Use the flame of a match or candle.

6.Follow the preceding steps for each appliance connected to the common venting system.

7.After it has been determined that each appliance remaining connected to the common venting system properly vents when tested as outlined above, return doors, windows, exhaust fans, fireplace dampers, and any other fuel burning appliance to their previous condition of use.

8.If improper venting is observed during any of the above tests, the common venting system must be corrected.

See National Fuel Gas Code, ANSI Z223.1 (latest edition) or CAN/CGA B149.1 & .2 Canadian Installation Codes to correct improper operation of common venting system.

Page 6 of 13

Issue 0902

506252-01

4)PCE(13, 15), (2 specifications

Allied Air Enterprises, a prominent name in the heating, ventilation, and air conditioning (HVAC) industry, specializes in manufacturing high-quality residential and commercial HVAC systems. With a strong commitment to innovation and efficiency, they have established themselves as a vital player in the market, driven by their dedication to delivering advanced climate control solutions.

One of the standout features of Allied Air Enterprises is their extensive product range, which includes air conditioners, heat pumps, gas furnaces, and indoor air quality solutions. This variety allows consumers to find tailored HVAC solutions that meet their specific needs, whether for a home environment or a larger commercial setting. The company emphasizes energy efficiency, ensuring their products are designed to minimize energy consumption while maximizing comfort.

Technologically, Allied Air Enterprises integrates cutting-edge innovations into their products. Many of their systems come equipped with advanced diagnostics and communication capabilities that allow for remote monitoring and control. This not only enhances user convenience but also streamlines maintenance, making it easier for technicians to identify and rectify issues before they become major problems.

Another key characteristic of Allied Air's offerings is their commitment to sustainable practices. Many of their products are built to comply with stringent environmental standards, utilizing refrigerants with lower global warming potential and employing manufacturing processes that reduce waste. This focus on sustainability resonates with environmentally-conscious consumers looking to reduce their carbon footprint.

Allied Air Enterprises also invests heavily in research and development to keep pace with the rapidly evolving HVAC landscape. Their ongoing efforts to innovate include exploring smart home integration and advancements in variable-speed technology, providing users with even greater levels of comfort and efficiency.

Customer support is another pillar of their business model. Allied Air prides itself on providing exceptional service, offering robust warranties and easy access to repairs and replacement parts, ensuring that their clients receive the best possible experience throughout the lifespan of their products.

In summary, Allied Air Enterprises stands out in the HVAC market through its commitment to innovation, energy efficiency, and customer satisfaction. With a diverse product lineup that integrates cutting-edge technology and sustainable practices, they are positioned to meet the evolving demands of both residential and commercial clients, making them a trusted choice in climate control solutions.