Philips MC-122 manual Important notes for users in the U.K, Mains plug, How to connect a plug

Page 2

Important notes for users in the U.K.

Mains plug

This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows:

1Remove fuse cover and fuse.

2Fix new fuse which should be a BS1362 5 Amp, A.S.T.A. or BSI approved type.

3Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place.

If the mains plug contains a fuse, this should have a value of 5 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp.

Note: The severed plug must be disposed of to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured with the following code: blue = neutral (N), brown = live (L).

As these colours may not correspond with the colour markings identifying the terminals in your plug, proceed as follows:

–Connect the blue wire to the terminal marked N or coloured black.

–Connect the brown wire to the terminal marked L or coloured red.

–Do not connect either wire to the earth terminal in the plug, marked E (or e) or coloured green (or green and yellow).

Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the two wires.

Copyright in the U.K.

Recording and playback of material may require consent. See Copyright Act 1956 and The Performer’s Protection Acts 1958 to 1972.

Italia

DICHIARAZIONE DI CONFORMITA’

Si dichiara che l’apparecchio MC-120, MC-122, MC-130 Philips risponde alle prescrizioni dell’art. 2 comma 1 del D.M. 28 Agosto 1995 n. 548.

Fatto a Eindhoven

Philips Consumer Electronics

Philips, Glaslaan 2

5616 JB Eindhoven,The Netherlands

Norge

Typeskilt finnes på apparatens underside.

Observer: Nettbryteren er sekundert innkoplet. Den innebygde netdelen er derfor ikke frakoplet nettet så lenge apparatet er tilsluttet nettkontakten.

For å redusere faren for brann eller elektrisk støt, skal apparatet ikke utsettes for regn eller fuktighet.

CAUTION

Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.

2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Audio Mains plug How to connect a plugImportant notes for users in the U.K Copyright in the U.KTuner Tape AUX Klass 1 laseraparat 142 108125 159Contents General Information Supplied accessoriesSafety Information Environmental InformationRear connections PowerPreparations Antennas ConnectionOptional connection Inserting batteries into the remote controlConnecting other equipment to your system FM AntennaControls on the system and remote control Power-saving automatic standby Switching the system onAdjusting volume and sound Basic FunctionsSelecting a different track CD OperationPlaying a disc Finding a passage within a trackReviewing the programme Different play modes Shuffle and RepeatProgramming track numbers Erasing the programmeProgramming radio stations Tuning to radio stationsRadio Reception Automatic programmingRDS News and Traffic Announcement TA Tuning to preset radio stationsSearching programme type PTY Scrolling through different RDS informationNot work while recording a tape Disarming RDS News and Traffic AnnouncementTape Operation / Recording General information on recordingRecording from the radio MaintenanceRecording from Aux B CSetting the timer Clock/TimerSetting the clock Specifications Activating and deactivatingTroubleshooting Problem SolutionClock/Timer setting is erased Remote control does not functionTimer is not working Properly
Top Page Image Contents