Amana W10326797A manual Electrical Requirements, Freezer Door, Recommended grounding method

Page 5

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your freezer into its final location, it is important to make sure you have the proper electrical connection.

Recommended grounding method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your freezer be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn the Temperature Control to the OFF position as shown and then disconnect the freezer from the electrical source.

Freezer Door

TOOLS NEEDED: ⁵⁄₈" hex-head socket wrench, ¹⁄₄" hex-head socket wrench, ¹⁄₂" hex-head socket wrench, ³⁄₈" hex-head socket wrench, #2 Phillips screwdriver, flat-blade screwdriver, ⁵⁄₁₆" open- end wrench, flat 2" putty knife.

IMPORTANT:

■All graphics referenced in the following instructions are included later in this section after “Final Steps.” The graphics shown are for a right-hand swing door (hinges factory installed on the right).

■If you only want to remove and replace the door, see the “Remove Door and Hinges” and “Replace Door and Hinges.”

■Before you begin, turn the control OFF, and remove food and adjustable door or utility bins from door.

Install and Remove Handle

NOTE: If reversing the door swing, move the handle from one side of the door to the other side.

To install handle:

1.Place the handle on the door as shown. See Handle graphic.

2.Using a flat-blade screwdriver, attach the handle to the door with the four handle screws (provided).

3.Place the trim pieces on the upper and lower handle ends as shown.

4.Apply firm pressure with your hand on the face of the trim. Slide the top trim down and the bottom trim up toward the handle.

To remove handle:

1.Remove the top and bottom trim.

2.Using a flat-blade screwdriver remove the four handle screws and lift off the handle.

Remove Door and Hinges

⁵⁄₁₆" Hex-Head Hinge Screw

1.Unplug freezer or disconnect power.

2.Open freezer door and remove base grille from the bottom front of the freezer. See Base Grille graphic 1A.

3.Close the freezer door and keep it closed until you are ready to lift it free from the cabinet.

NOTE: Provide additional support for the door while the hinges are being moved. Do not depend on the door magnets to hold the door in place while you are working.

4.Remove the parts for the top hinge as shown in Top Hinge graphic 1B.

5.Lift the freezer door free from the lower hinge and cabinet and set aside.

6.Remove three hex head hinge screws and bottom hinge assembly. See Bottom Hinge graphic 1C.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents W10326797A Upright FreezerTable DES Matières Table of ContentsBefore You Throw Away Your Old Freezer or Refrigerator Freezer SafetyClean Before Using Installation InstructionsUnpacking LocationRequirementsRecommended grounding method Electrical RequirementsFreezer Door Reverse Door optional on some models CabinetReplace Door and Hinges Final StepsDoor Swing Reversal optional Adjust the DoorFreezer USE Using theControlEnsuring Proper Air Circulation Key Eject LockFreezer Care Freezer FeaturesBase Grille Defrosting and Cleaning Your Manual Defrost FreezerTo Remove and Replace the Base Grille Style 1-Models with a drain systemPower Interruptions TroubleshootingChanging the Light Bulb Moving CarePage Accessories Assistance or ServiceU.S.A InCanadaThis limited warranty does not cover Amana Major Appliance WarrantyVotre sécurité et celle des autres est très importante Sécurité DU CongélateurEmplacement d’installation Instructions DinstallationDéballage Enlèvement des matériaux d’emballagePortesdu congélateur Méthode recommandée de mise à la terreSpécificationsélectriques Étapes finales Réinstallation Portes et charnièresCaisse Dépose et réinstallation De la porte Ajustement de la commande de température Utilisation de la commandeAjustement de porte Congélation rapide sur certains modèlesCongélateur Nettoyage du congélateur sans givre Entretien DU CongélateurGrille de la base Dégivrage et nettoyage du congélateur Dégivrage manuelStyle 2-modèles sans système d’écoulement Remplacement delampoule d’éclairageStyle 1-modèles avec système d’écoulement Déménagement DépannagePannes de courant électrique La porte est-elle fermée complètement? Le moteur semble fonctionner excessivementAccessoires Assistance OU ServiceSi vous avez besoin de pièces de rechange Nos consultants fournissent l’assistance pourLa présente garantie limitée ne couvre pas Garantie DES Gros Appareils Ménagers AmanaW10326797A

W10326797A specifications

The Amana W10326797A is a high-quality washer/dryer combo that combines efficiency, versatility, and advanced technology to cater to modern laundry needs. Designed to fit seamlessly into various kitchen and laundry configurations, this appliance stands out for its performance and user-friendly features.

One of the main highlights of the Amana W10326797A is its spacious capacity, allowing users to tackle large loads of laundry effectively. With ample space inside the drum, families can wash larger items, such as blankets and comforters, without requiring multiple cycles. This convenience not only saves time but also enhances the overall laundry experience.

The washer/dryer combo employs advanced cleaning technologies designed to deliver thorough and gentle washing. With multiple wash cycles, users can choose the right setting for their fabric types, ensuring optimal care and longevity of their garments. The machine also features a robust spin cycle that efficiently removes excess water from clothes, reducing drying time and saving energy.

Energy efficiency is a significant characteristic of the Amana W10326797A. It utilizes innovative technologies to minimize water and electricity consumption without compromising on performance. This not only benefits the environment but also leads to reduced utility bills, making it a smart choice for budget-conscious households.

Another standout feature is the intuitive control panel, which provides easy navigation through the various settings and options available. LED indicators and clear labels guide users in selecting the right cycle and managing their laundry tasks with ease. Additionally, the delay start option allows users to set the machine to begin washing or drying at a more convenient time, enhancing flexibility.

Durability is also a key aspect of the Amana W10326797A. Built with high-quality materials, this appliance is designed to withstand the rigors of regular use while maintaining performance over the long term. The stylish design adds a modern touch to any laundry area, making it not only a practical appliance but also an aesthetic one.

In summary, the Amana W10326797A combines a spacious capacity, versatile washing options, energy efficiency, and user-friendly controls, making it a noteworthy choice for those looking for an effective washer/dryer combo. Its durable construction and modern design further enhance its appeal, ensuring it meets the demands of contemporary lifestyle while providing exceptional laundry care.
Top Page Image Contents