Transport instructions, Disposal, Device setup

Transport instructions

The device should be transported only in upright position.

The packing as supplied must be intact during transportation.

After a transport in the horizontal position, the device may only be taken into operation 4 hours after being stood up vertically again. The appliance must be protected against rain, moisture and other atmospheric influences. The manufacturer assumes no liability if safety instructions are disregarded.

Disposal

Make the device unusable immediately. Pull out the mains plug and cut the power cable. Remove or destroy snap or latch locks before disposing of the device. In this manner you prevent children from locking themselves in and endangering their lives.

Device setup

•Do not operate your appliance in a room where the temperature is likely to fall below 10 °C at night and/or especially in winter. At lower temperatures the appliance may not operate, resulting in a reduction in the storage life of the food.

•The climate class rate of your appliance is given in Technical Features leaflet and written on the rating label inside the appliance. It specifies the appropriate operating ambient temperatures as explained below.

Climatic class	Ambient temperatures
SN	+10 °C to 32 °C
N	+16 °C to 32 °C
ST	+18 °C to 38 °C
T	+18 °C to 43 °C
SN-ST	+10 °C to 38 °C
SN-T	+10 °C to 43 °C

Location

Only place the device in dry rooms which can be aired.

Avoid direct sunlight or direct heat sources such as a stove or a heater.

If this cannot be avoided, the following minimum distances should be maintained: Electric stoves: 3,00 cm

Heater: 3,00 cm

Cooling devices: 2,50 cm

•Ensure sufficient air circulation for your device.

•Make sure that sufficient room is provided around the appliance to ensure free air circulation.

Fit the two plastic wall spacers supplied with the appliance rotating 1/4 turn to the condenser at the back of the appliance (Fig. 3).

•The device should be located on a smooth surface. The two front feet can be adjusted as required. To ensure that your appliance is standing upright adjust the two front feet by turning clockwise or counter-clockwise, until the product is in firm contact with the floor. Correct adjustment of feet avoids excessive vibration and noise.

Electrical connections

Warning

This device must be grounded.

•Check whether the power type and voltage in the device location corresponds to the one stated on the rating label inside the device.

•The electrical safety of the device is only assured when the grounding system in the house is installed in accordance with regulations.

•When putting the device in, do not stand it on the power cable, otherwise the cable will be damaged.

•Ensure that the plug remains readily accessible. Do not use multiple adapter bar or extension cable.

D 9459 NM specifications

The Beko D 9459 NM is a state-of-the-art tumble dryer, designed to deliver exceptional drying performance and efficiency. Its sleek design and user-friendly features make it a popular choice among households seeking reliable laundry solutions. With a variety of advanced technologies, this model ensures that clothing is dried to perfection while minimizing energy consumption.

One of the standout features of the Beko D 9459 NM is its Heat Pump technology. This innovative system works by recycling hot air generated during the drying process, which not only reduces energy consumption but also protects your clothes from excessive heat. By gently drying fabrics at lower temperatures, users can enjoy the peace of mind that their garments will maintain their color and texture over time.

Another significant characteristic of this dryer is its large capacity of 9 kg, making it ideal for families or those with substantial laundry needs. This ample drum size allows users to dry larger loads in a single cycle, saving time and energy. Moreover, the design incorporates a ProSmart Inverter Motor that ensures quieter operation and enhanced durability. This motor technology also contributes to energy efficiency, as it adjusts the dryer’s performance to match the load, optimizing power usage.

In addition, the Beko D 9459 NM features an array of drying programs tailored to different fabric types. From delicate items to heavy-duty towels, this dryer offers specialized cycles to ensure that every piece of clothing is treated appropriately. The sensor drying function is particularly noteworthy, as it detects moisture levels in the drum and automatically adjusts drying times, preventing over-drying and safeguarding garments.

The User Interface is designed with simplicity in mind, featuring a clear digital display that allows for easy program selection and monitoring. With options for quick drying and an anti-creasing function, users can enjoy both convenience and efficiency. Furthermore, this model also includes a self-cleaning condenser, which maintains optimal performance by removing lint buildup without the need for manual cleaning.

Overall, the Beko D 9459 NM is a versatile and energy-efficient tumble dryer, equipped with advanced features that cater to modern laundry requirements. Its thoughtful design and technological innovations make it a go-to appliance for those seeking reliability, efficiency, and care for their clothes.