Hoover HHI 694 manual Operation, Functioning 5-key electronic model

is central with respect to the motor housing.

6.Filtering version only: install a section of a tube, long enough to reach the connection ring on the motor housing (Fig.1), onto the F deflector.

7.Mount motor housing J (Fig. 1) to the lattice girder with 4 large S screws (Fig. 3) so that the side with the electronic and connection boxes are on the front part.

8.Connect the discharge tube.

9.Fix bracket K (Fig. 3-Fig. 4-Fig. 4.1), which supports the electronic box and the connection box, to the motor housing with 2 screws.

10.Insert the M commands box into apposite N sealing rail (Fig. 4.2 – Fig. 4.3).

Note! The drawing shows a type of commands box. This can be equipped with a number of different keys and leds depending on the model possessed.

11.Connect to the domestic electric power.

12.Mount upper flue O onto the lattice girder with the 2 A screws (Fig. 5).

Note: the upper flue is reversible. It is possible to install it with air exit slit H (Fig. 5) upward (filtering version) or downward (suction version) so as to be hidden when the lower flue is mounted (in this case, however, the total extension of the flues will be reduced).

Attention! Insert the flue carefully so as to avoid damaging the electric cables and the commands box.

13.Mount lower flue P and fix it to the lower part of the motor housing with two screws Q (Fig. 5)

Note: Do not tighten completely!

Attention! Insert the flue carefully so as not to avoid damaging the electric cables and the commands box.

14.Mount spacer ring S (Fig. 5) or the mantel, when envisaged.

15.Tighten screws Q (Fig. 5) with decision.

16.Remove the carbon filter holding frame and tighten internal screw R (Fig. 4.3) that adjusts the position of the commands box so that the keys extrude from the flue.

Block the position tightening the lock nut on the screw.

17.Remove central screw T (Fig. 5), placed between the bulbs, temporarily and fix filter holder mask U (Fig. 5) with it.

Operation

Use the high suction speed in cases of concentrated kitchen vapours. It is recommended that the cooker hood suction is switched on for 5 minutes prior to cooking and to leave in operation during cooking and for another 15 minutes approximately after terminating cooking.

Functioning - 5-key electronic model

O			1	2 3			O	I
				F C
1	2	3	4	5	6	7	8	9

9

1.Motor OFF button

2.ON button and motor speed selection button 1 - 2 - 3 - 1 - 2 - . . . .

3.Speed 1 LED

4.Speed 2 LED and metal grease filter saturation LED (in this latter case, the LED will flash - See instructions on grease filter cleaning).

Once the grease filters have been cleaned, press button 1 for about 3 seconds until you hear the acoustic signal (beep): the LED 4 will now stop flashing.

5.Speed 3 LED and active carbon filter saturation LED (in this latter case, the LED will flash - See instructions on active carbon filter replacement).

Once you have replaced the charcoal filter, press button 1 for about 3 seconds until you hear the acoustic signal (beep). LED 5 will now stop flashing.

Warning!

The active carbon filter saturation LED is not activated. In order to activate the active carbon filter saturation indicator, press buttons 2 and 7 simultaneously for 3 seconds. Initially, only LED 4 will flash, then after the 3 seconds have passed, LED 5 will also start flashing, indicating that the active carbon filter saturation control system is active.

To switch off the system, re-press the same two buttons: after 3 seconds LED 5 will stop flashing and the device will be switched off.

6.Intensive speed LED

7.Intensive speed ON switch

This speed should be used when the concentration of cooking fumes or odours is particularly strong (for example when frying, cooking fish etc.).

The fast speed will run for about 5 minutes and then return to the speed previously set automatically (1, 2 or 3), or switch off if no speed was selected.

To turn off the fast speed, before the end of the 5 minutes, press button 1 or button 2.

8.OFF lamp button

9.ON lamp button

If the hood fails to operate correctly, briefly disconnect it from the mains power supply for almost 5 sec. by pulling out the plug. Then plug it in again and try once more before contacting the Technical Assistance Service.

Model with button panel

E A B C D

A. on/off light switch

B. on/off aspiration switch and minimum power selection B+C. medium power selection aspiration switch

B+D. maximum power selection aspiration switch

E. operating gauge (foreseen in the model with round buttons)