Indesit KD3G21/G, KD3G2/G manual Use of Hotplates, Practical Advice on Using the Burners

Page 14

Use of Hotplates

Practical Advice on Using the Burners

To use the burners as efficiently as possible, some basic guidelines should be followed:

Use cookware that is the right size for each burner (see table) in order to prevent the flame from spreading beyond the bottom of the cookware.

Only use cookware with flat bottoms.

As soon as the boiling point is reached, turn the knob to the lowest setting.

Always use lids with pots and pans.

Burner

ø Cookware diameter (cm)

 

 

Fast (R)

24 - 26

 

 

Semi Fast (S)

16 - 20

 

 

Auxiliary (A)

10 - 14

 

 

N.B.: On models equipped with a reduction grid, the grid should only be used with the auxiliary burner when cookware with a diameter of less than 12 cm is used.

1.Press the ignition button and then push in and turn the control knob of the chosen burner anti-clockwise to the large flame symbol. Continue to press the ignition button until the sparks light the gas.

2.Turn the control knob anti-clockwise to the desired setting. Only turn the control knob between the large flame symbol and the small flame symbol for adjusting the setting.

3.To turn off, turn the control knob fully clockwise to the symbol O.

DO NOT use the hotplate unless all pan supports are in position.

DO NOT use mis-shapen pans which may be unstable.

DO NOT use round base woks directly on the pan supports.

DO NOT use the glass lid (if fitted) as a working surface.

Each burner is fitted with a spark ignitor for lighting the gas. To ensure rapid lighting of the burners every time they are used, the ignitors must be kept clean and dry. Remove any food spillage or cleaning materials from the electrode using a small nylon brush such as a tooth brush. Access to the electrode can be achieved by lifting off the loose burner parts carefully when the burners are cool.

When the hotplate burner bodies and caps are removed for cleaning, be careful not to drop any food particles or cleaning materials into the burner bases, to avoid the possibility of blocking the gas jets.

If aluminium based pans are used, a silvery deposit may appear on the top edge of the pan support fingers. See 'Care and Cleaning' section for cleaning information.

SAFETY REQUIREMENTS FOR DEEP FAT FRYING

1.Never fill chip pans more than one third full with oil or fat.

2.Never leave oil or fat unattended during the heating or cooling period.

3.Never heat fat or fry with a lid on the pan.

4.Always dry food thoroughly before frying, and lower it slowly into the hot oil or fat. Frozen foods in particular will cause frothing and spitting if added too quickly.

5.Always keep the outside of the pan clean and free from streaks of oil or fat.

HOW TO DEAL WITH A FAT FIRE

1.Do not move the pan.

2.Turn off the hotplate burners.

3.Smother the flames with a fire blanket or damp cloth to extinguish the fire. Do not use water or a fire extinguisher as the force of it may spread the burning fat or oil over the edge of the pan.

4.Leave the pan for at least 60 minutes before moving it.

14

Image 14
Contents 50cm Free Standing Gas Cooker Contents Introduction Installation Installation of the cookerConnecting the gas supply Gas connectionElectrial connection Replacement fuse coversHow to connect an alternative plug Replacing the fuseAdapting to different types of gas Disposing of the applianceAdapting the cooker to different types of gas Adapting the gas grill to different types of gas Fig. ELiquid Gas Natural Gas Burner and Nozzle SpecificationsKD3G21/G Safety Information AlwaysSafety Information Never Extinguisher is likely to tip the pan overFeatures Control Knobs for the gas burners TimerControl Panel Electronic Ignition For the Gas HobBurner Cookware diameter cm Practical Advice on Using the BurnersUse of Hotplates Burner GrillingRelighting‘ HandleOven Main OvenOven Cooking Chart Care and Cleaning Problem Check Grilling Cooking Results Not Satisfactory?Problem Something Wrong with your Cooker?Contact the Service Office 0870 If It Still Won’t WorkVoltage and Frequency Technical CharacteristicsMain Oven BurnersPage Key Contacts