Multiquip MC-92S manual MC-92P/S Concrete Mixer Electric Motor, Electric Motor Connection

Page 18

MC-92P/S CONCRETE MIXER — ELECTRIC MOTOR

Electric Motor

For maintenance care and operation of the electric motor, refer to your electric motor instruction booklet furnished with the electric motor.

Protect the electric motor from dust as much as possible and keep ventilating openings clean.

CAUTION:

DO NOT spray water at any time on the electric motor.

DO NOT operate electric motor in a explosive environment.

The electric motor used in this mixer is a single-phase 1.5 HP motor. The input voltage requirement for this motor is either 115 or 230 VAC only.

Electric Motor Connection

A 12 inch electrical cable (Figure 2) with a pigtail at one end is provided with the electrical motor for hookup to a power source. Table 1. shows the required NEMA connector for the desired motor horsepower rating. In addition, Table 2 also shows the matching NEMA approved connector for the required extension cord.

ALWAYS, make certain that the power source required for the electric motor is correct and always use the correct NEMA configuration plug. Failure to supply the correct voltage to the motor can severely damage the motor.

The electric motor supplied with the mixer is configured from the factoryfor115VACgroundedoperation.Makecertainthatthecorrect size grounded (3-wires) extension cord is used.SeeTable 5.

Motors can burn out when the line voltage falls 10% below the voltage rating of the motor. Failure to use proper voltage will cause the motor to overheat and actuate the overload switch.

If overload protection should actuate because of improper voltage or any other malfunction, turn the main switch on the motor to the "OFF" position and correct the problem, press the reset switch button, and turn the main switch to the "ON" position.

Table 5. Recommended Extension Cord Sizes

Electric

Input

50 ft.

75 ft.

100 ft.

200 ft.

Motor

Voltage

(15.24 m)

(22.86 m)

(30.48 m)

(60.96 m)

 

 

 

 

 

 

 

115 VAC

No. 12

No. 10

No. 8

No. 6

1.5 HP

 

 

 

 

 

230 VAC

No. 14

No. 12

No. 12

No. 8

 

 

 

 

 

 

 

Electric MotorVoltage Change Switch

1.ALWAYS make certain the electric motor's ON/OFF switch is in the "OFF" position and the power cord has been disconnected from the power source.

2.Remove the voltage change lock-out bolt and nut (Figure 6). Change the position of the voltage change toggle switch from 115VAC to 230VAC.The mixer is factory wired for 115 VAC operation.

3.Re-install the voltage change lock-out bolt and nut.

Figure 6. Voltage Change Switch

4.Important!, when changing the input voltage to the electric motor from 115 to 230 VAC, the plug on the electric motor power cord must also be changed. SeeTable 6 and Figure 7.

Table 6. Electric Motor Wiring Information

Motor

115-230 VAC - Single Phase

Horsepower

 

 

NEMA Plug Connector

Mating NEMA

Rating

 

Receptacle Connector

 

 

 

 

 

1.5 HP

L5-20P P/N EM940537

L5-20R P/N EM940538

(115 VAC)

 

 

 

 

 

1.5 HP

L6-20P P/N 940539

L6-20R P/N 940540

(230 VAC)

 

 

 

 

 

 

NEVER! disable or disconnect the

NOTE

ON/OFF switch on the electric motor.

It is provided for operator safety.Injury

 

 

may result if it is disable, disconnected

 

or improperly maintained.

PAGE 18 —MC-92P/S CONCRETE MIXERS — OPERATION AND PARTS MANUAL — REV. #7 (09/13/07)

Image 18
Contents Models Proposition 65WARNING Page MC-92P/S Concrete Mixer Table of Contents MC-92P/S Concrete Mixer Parts Ordering Procedures Best Deal! Order via Internet Dealers OnlyOrder via Fax Dealers Only MC-92P/S Concrete Mixer Specifications Specifications Engines/Electric MotorMC-92P/S Concrete Mixer Dimensions Mixer Mixer DimensionsMC-92P/S Concrete Mixer Safety Message Alert Symbols Foryour Safety and the Safety of OthersGeneral Safety MC-92P/S Concrete Mixer Rules for Safe OperationMC-92P/S Concrete Mixer Rules for Safe Operation EmergenciesMC-92P/S Concrete Mixer Operation and Safety Decals Machine Safety DecalsMC-92P/S Concrete Mixer General Information MC-92P/S Concrete Mixer Mixer Basic Components Mixer Major ComponentsMC-92P/S Concrete Mixer Basic Engine Components Engine Controls and ComponentsMC-92P/S Concrete Mixer Handwheel Assembly AssemblyTow Bar to Vehicle Connection Coupler Only Mixer Tow Bar Vehicle Connection Pintle and LoopMC-92P/S Concrete Mixer Safety Chain Connection Tow Bar to Mixer ConnectionElectric Motor Electric MotorVoltage Change SwitchMC-92P/S Concrete Mixer Electric Motor Electric Motor ConnectionSingle Phase Electric Motor with 12 inch Pigtail Cable MC-92P/S Concrete Mixer Electric MotorMC-92P/S Concrete Mixer PRE-INSPECTION GAS Engine MC-92P/S Concrete Mixer Initial START-UP GAS Engine Starting the Engine Gasoline OnlyMC-92P/S Concrete Mixer Initial START-UP Electric Motor Initial Start-up Instructions Electric Motor StartingStarting the Electric Motor MC-92P/S Concrete Mixer Operation OperationStopping the Mixer Electric MC-92P/S Concrete Mixer Maintenance Engine Engine Maintenance ScheduleMC-92P/S Concrete Mixer Maintenance Engine MaintenanceMC-92P/S Concrete Mixer Maintenance Mixer MC-92P/S Concrete Mixer Maintenance Mixer Suspension ComponentsTo tighten wheel lug nuts Page MC-92P/S Concrete Mixer Troubleshooting Engine Engine TroubleshootingMC-92P/S Concrete Mixer Troubleshooting ENGINE/MIXER Engine TroubleshootingPart NO. Column Explanation of Code in Remarks ColumnNO. Column QTY. ColumnMC-92P/S Concrete Mixer Suggested Spare Parts Qty DescriptionMC-92P/S Concrete Mixer Name Plate and Decals Name Plate and DecalsMC-92P/S Concrete MIXER- Name Plate and Decals MC-92P/S Plastic Barrel Plastic Barrel AssyNUT, Lock 3/8 NC HOUSING, JackshaftRing Gear PLUG, ExpansionMC-92P/S Steel Barrel Steel Barrel AssyShim 0.14 Thick BARREL, Steel 9 CU. FTShim 0.10 Thick Shim 0.187 ThickMC-92P/S Main Frame Assembly Main Frame AssyGUARD, Gear Wheel Handwheel Safety ChainConnector Link WASHER, Lock 1/4MC-92P/S Axle Assembly Axle AssySpring Leaf Lock NUT 5/8 NCSpring Support Axle 1-1/16 SpindleMC-92P/S Cabinet Assembly Cabinet AssyWASHER, Flat 5/16 Rubber ProtectorCABINET, Engine Assy Latch ASSY., CompleteMC-92P/S GAS Engine Mounting Plate Assembly GAS Engine Mounting Plate AssyRING, Retaining ENGINE, Honda 8.0 HPENGINE, Robin 8.5 HP Square KEYMC-92P/S Electric Motor Mounting Plate Assembly Electric Motor Mounting Plate AssyMOTOR, Electric 1.5 HP Honda GX240K1HA2 Engine AIR Cleaner Assy AIR Cleaner AssyGROMMET, AIR Cleaner ELEMENT, AIR CLEANER, DualCOVER, AIR Cleaner COLLAR, AIR CleanerHonda GX240K1HA2 Engine Camshaft Assy Camshaft AssyROD Push SPRING, Weight ReturnCamshaft ARM Valve RockerHonda GX240K1HA2 Engine Carburetor Assy Carburetor AssyValve SET, Float PLATE, Lever SettingGasket SET Float SETHonda GX240K1HA2 Engine Control Assy Control AssySPRING, Governor ARM, GovernorROD, Governor SPRING, Throttle ReturnHonda GX240K1HA2 Engine Crankcase Cover Assy Crankcase Cover AssyPIN, Governor Weight WEIGHT, GovernorHOLDER, Governor Weight Type BalancerHonda GX240K1HA2ENGINE Crankshaft Assy Crankshaft AssyWeight Balancer Honda GX240K1HA2 Engine Cylinder Barrel Assy Cylinder Barrel AssyBOLT, Drain Plug Switch ASSY., OIL LevelSHAFT, Governor ARM Ring 14MM AraiHonda GX240K1HA2 Engine Cylinder Head Assy Cylinder Head AssyCLIP, Valve Guide GUIDE, VALVE, OS, OptionalGUIDE, EX. VALVE, OS, Optional GASKET, Cylinder HeadHonda GX240K1HA2 Engine FAN Cover Assy FAN Cover AssyCLIP, Tube Switch ASSY., Engine StopCLIP, Wire Harness ShroudHonda GX240K1HA2 Engine Flywheel Assy Flywheel AssyNUT, Special 16MM FAN, CoolingFlywheel Comp KEY, Special WoodruffHonda GX240K1HA2 Engine Muffler Assy Muffler AssyPROTECTOR, EX. Pipe MufflerPROTECTOR, Muffler PIPE, EXHonda GX240K1HA2 Engine Fueltank Assy Fuel Tank AssyTank COMP., Fuel *NH1*, Black Rubber Supporter 107MMJOINT, Fuel Tank GASKET, Fuel Filler CAPHonda GX240K1HA2ENGINE Ignition Assy Ignition Coil AssyCoil ASSY., Ignition GROMMET, WireWIRE, Stop Switch 370MM CAP ASSY., Noise SuppressorHonda GX240K1HA2 Engine Piston Assy Piston AssyRing SET, PISTON, 0.75, Optional BOLT, Connecting RODRing SET, PISTON, STD PISTON, StandardHonda GX240K1HA2 Engine Recoil Starter Assy Recoil Starter AssySPRING, Friction PULLEY, Recoil StarterRATCHET, Starter SPRING, Starter ReturnHonda GX240K1HA2 Engine Gear Reduction Assy Gear Reduction AssySHAFT, P.T.O. H- Type GEAR, Primary Drive 17TCountershaft Shim a OptionalHonda GX240K1HA2 Engine Label Assy Label AssyMARK, CAUTION, External Labels AssyEMBLEM, Internal LABEL, CautionTerms and Conditions of Sale Parts Freight PolicyPage HERE’S HOW to GET Help

MC-92P, MC-92S specifications

The Multiquip MC-92S and MC-92P are high-performance concrete mixers designed for professional use in construction and masonry applications. These models offer a blend of power, durability, and user-friendly features, catering to the demands of contractors and construction workers who require reliable equipment for mixing concrete, mortar, and other materials.

The MC-92S is equipped with a robust 9.0 horsepower Honda gasoline engine that provides ample power for even the most demanding mixing tasks. This model features a 9 cubic feet capacity drum, allowing for larger batches of mixed material. The MC-92S is designed with a heavy-duty steel frame that enhances its durability and stability during operation. The drum is constructed with abrasion-resistant steel, ensuring longevity and minimizing wear over time.

In contrast, the MC-92P utilizes a powerful 9.0-horsepower propane engine, making it an excellent choice for users who prefer cleaner fuel options. This model retains many of the same design features as the MC-92S, including the enhanced drum capacity and rugged frame. The propane engine not only provides a quieter operation but also reduces emissions, making it a more environmentally friendly option without compromising performance.

One of the standout technologies in both models is the innovative mixing mechanism. The unique design of the mixing blades ensures efficient and consistent blending of materials, reducing the time required for mixing and enhancing the quality of the final product. Additionally, the MC-92 series features a manual dump system, which allows operators to easily and accurately discharge mixed material from the drum.

Safety is a primary concern in construction, and Multiquip has incorporated several safety features into these mixers. The control panel is designed for easy access and includes safety switches that prevent accidental start-up. The sturdy base and low center of gravity provide stability during operation, reducing the risk of tipping.

In summary, the Multiquip MC-92S and MC-92P concrete mixers are exceptional tools for professionals needing reliable, efficient, and versatile mixing equipment. With their powerful engines, capacity, durability, and innovative mixing technologies, they stand out in the competitive market of concrete mixers, ensuring that construction projects run smoothly and efficiently.