Multiquip WM-120PM operation manual WM-120P/S Towing, Step, Check the following before towing

Page 13

NOTE

Before towing, check with local and state laws for proper compliance.

The tow bar and chain must be properly attached to the mixer and towing vehicle prior to towing. Refer to the following installation instruction:

Step 1.

Insert the Draw Bar into the main frame. Secure, utilizing the 3/4" bolt (grade 5) and nylock nut.Tighten to 100 foot pounds.

STEP 1

DRAW BAR

BOLT & NUT

Step 2.

Install the chain through the hole located between the frame gusset and frame angle. Loop the chain together and place under the Draw Bar. Secure with connector link.

INSERT CHAIN THROUGH

STEP 2

THE HOLE

 

 

DRAW BAR

FRAME ANGLE

 

FRAME GUSSET

CONNECTOR LINK

Step 3.

Extend the chain along the length of the Draw Bar, remove excess chain (slack) and secure to bottom connector link. Secure the chain to the towing vehicle, using the connector link.

WM-120P/S — TOWING

STEP 3

VEHICLE

CONNECTOR LINK

DRAW BAR

REMOVE EXCESS

CHAIN (SLACK)

BOTTOM CONNECTOR LINK

NOTE

It is critical that the length of the chain be properly adjusted, to prevent the Draw Bar and the front mixer stand from dropping to the ground (contact) in the event the Draw Bar becomes disconnected from the towing vehicle.

If a new safety chain is required use P/N 13363. For a new connector link use P/N 01004.

CAUTION:

■Check the following before towing:

BALL HITCH COUPLER

1.Check vehicle hitch, ball, and coupler for signs of wear or damage. Replace any parts that are worn or damaged before towing.

2.Use only the 2" ball diameter as indicated on your coupler. Use of any other ball diameter will create an extremely dangerous condition which can result in separation of the coupler and ball or ball failure.

3.Be sure the coupler is secured to the hitch ball and the lock lever is down tight and locked.

Recheck tightness again after towing about 50 miles.

4.Check that trailer safety chains are properly connected.

WHITEMAN WM-120P/S — PARTS & OPERATION MANUAL — REV. #6 (07/20/05) — PAGE 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents PLASTER/MORTAR Mixers Page Heres HOW to GET Help Engines UPS Ground Service at no charge for freight Parts Ordering ProceduresOperation and Safety Decals Safety InstructionsRules for Safe Operation General SafetyRules for Safe Operation Maintenance SafetyEmergencies WM120PM WM120SM WM120P/S SpecificationsGeneral WM120P/S General InformationMixer WM-120P/S ControlsWM-120P/S Electric Motor Electric Motor Wiring InformationStep WM-120P/S TowingCheck the following before towing Paddle Blade Adjustment, Polyethylene Drum WM-120P/S Paddle Blade AdjustmentWM-120P/S Paddle Blade Adjustment Startingthe Engine gasoline only WM-120P/S Initial START-UPStoppingthe Mixer gasoline WM-120P/S Initial START-UPStoppingthe Mixer electric Wheel Bearings WM-120P/S MaintenanceClutch Adjustment Mechanical 12 CF Mixer WM-120P/S MaintenanceClutch Adjustment Procedure Engine Troubleshooting Symptom Possible Problem Solution WM-120P/S -TROUBLESHOOTING EngineWM-120P/S -TROUBLESHOOTING ENGINE/MIXER Items Found In the Items Number Column WM-120P/S- Explanation of Code in Remarks ColumnWM-120PS 1TO 3 Units WM-120P/S- Suggested Spare PartsWM-120P/S Engine Side Paddle Assy Paddle ARM Engine Side WM-120P/S -TOW Side Paddle Assy Paddle ARM Center TOW Side WM-120P/S Paddle Shaft Assy WM-120P/S Paddle Shaft Assy WM-120P/S Polyethylene Drum Assy WASHER, FLAT, 3/8 SAE WM-120P/S Steel Drum Assy TUB, Steel WM-120P/S CAB Assy CAB DOOR, Complete Assy WM-120P/S FRAME,WHEEL,TIRE and HUB Assy Transmission Support BAR WM-120P/S Name Plate and Decals See Decal Illustrations on WM-120P/S -WISCONSIN Engine Assy 2HP Wisconsin Engine WM-120P/S Honda Engine Assy 11HP Honda Engine WM-120P/S Electric Motor Assy HP 1 Phase Elect Motor WM-120P/S -TRANSMISSION Assy Shifter Shaft Terms and Conditions of Sale Parts Page Multiquip INC

WM-120PM specifications

The Multiquip WM-120PM is a powerful and versatile water truck designed for a variety of applications, including construction, dust control, and agricultural usage. Engineered with performance and durability in mind, the WM-120PM is equipped with several advanced features and technologies that make it a standout choice in the water truck category.

One of the most notable features of the WM-120PM is its impressive 1,200-gallon capacity tank, allowing operators to cover large areas without frequent refills. The tank is constructed from high-quality materials that ensure longevity and resistance to corrosion, making it suitable for harsh environments. This capacity is paired with a robust pump system that provides reliable water distribution for various applications, including road maintenance and dust suppression.

The WM-120PM is equipped with a reliable engine and transmission system that delivers sufficient power for all terrains. Its drivetrain is designed to navigate both on and off-road conditions smoothly, ensuring that operators can transport water effectively to different job sites. Furthermore, the truck's compact design allows for excellent maneuverability, making it easy to operate in tight spaces and crowded areas.

Technology also plays a vital role in the WM-120PM's functionality. The water truck features an intuitive control panel that allows operators to manage water flow and spray patterns easily. This feature is particularly beneficial when adjusting the water distribution based on specific project needs, promoting efficiency and precision. Additionally, the truck can be fitted with optional spray nozzles and hoses for more specialized applications.

Safety is also a priority in the design of the WM-120PM. The truck includes features such as an anti-skid step for easy access and exit, and the braking system is designed to provide maximum control on inclines and declines. Visibility is enhanced with strategically placed lighting, ensuring that operators can work effectively even in low-light conditions.

In conclusion, the Multiquip WM-120PM water truck combines capacity, durability, and advanced technology to meet the diverse needs of various industries. Its rugged build, efficient pump system, customizable features, and safety enhancements make it an excellent solution for anyone requiring reliable water transportation and distribution. Whether for construction projects or agricultural applications, the WM-120PM proves to be a valuable asset in the field.
Top Page Image Contents