JBL PS1400 specifications Wall Mounting, Corner-Mounting the PT800 Tower

Page 8

Wall Mounting (Continued)

Install the two screws into either a wooden wall-stud or anchor, and tighten them until the back of each screwhead is about 1/8 inch from the wall.

Install the loudspeaker by slowly moving the cabinet

toward the screws so that the screwheads clear the larger circular portion of the top two keyholes of the two brackets. Once both screwheads have entered the keyholes, the loudspeaker should gently be

lowered onto the screw shafts. Check that the loudspeaker is firmly locked onto the screws by gently pulling the speaker down and forward.

Corner-Mounting the PT800 Tower

If desired, you may mount the PT800 towers in the corners of the room using the optional PCM800 corner-mount bracket. PCM800 corner-mounting kits are available separately from your JBL dealer.

NOTICE: Important Safety Notes

•Proper selection of mounting hardware and installation of the wall and/or corner brackets are the responsibility of the customer.

•This product is not intended for ceiling mounting.

Six Number 10 round head or pan head screws should be used per loudspeaker. The screw head should be between 3/8 inch and 13/32 inch in diameter, and the screw should be at least 2 inches in length. When installing screws through drywall, always use properly selected wall anchors.

Attach two pieces of the four self-adhesive rubber pads that came with the PT800 to the angled surfaces of the enclosure near the bottom to prevent the speaker from rattling against the wall and to allow a firm fit.

Select a suitable mounting location in a wall corner. (The ceiling is not a suitable mounting location.)

Hold the wall bracket against the wall with the U-shaped cutouts at the top. Make sure that it’s level and 3/4 inch below where you want to have the top of your PT800 enclosure positioned. Mark the center of each of the six mounting holes using a pencil or sharp implement. Remove the bracket and drill six pilot holes as required for your wood screws or anchors. Securely fasten the

bracket to the wall. You have access to the wall screws via the six large holes on the front face of the bracket.

Loosen, but do not remove, the two hex bolts on the back of the PT800 speaker cabinet. Back the screws out until the head is about 1/4 inch from the enclosure. Install the loud- speaker by slowly lowering the cabinet towards the U-shaped cutouts at the front top surface of the PCM800 bracket so that the hex bolt shafts rest in the cutouts. Check that the speaker is level, then tighten the hex bolts. Check that the loud- speaker is firmly locked onto all screws by gently pulling the speaker down and forward.

7

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Specification S D E L S PS1400, PT800, PC600N E R ’ S G U I D E N E P er f o rm an c e S e r i esAbove Powered subwoofer. ForBass without a PS1400 C L U D E D Hardware store, between the feet and the floor If you are not dockingPT800 tower and PS1400 Subwoofer modulesU N T I N G O P T I O N S Stacking the PT800 Tower on Top of the PS1400 SubwooferWall-Mounting the PT800 Tower or the PC600 Center Figures 4 and 4aWall Mounting Corner-Mounting the PT800 TowerOn/Auto Switch When Subwoofer Controls PS1400 OnlySystem Input These General Connection InformationLFE Level Control This Do not use the PS1400’s Internal crossoverPS1400 and PT800 are Separately on the wall, onRight Tower CenterRight Sub Left Surround Right SurroundCenter and rear channels From the mounting plate on top Left RightLeft and right Sub Configure the receiver Connect the receiver Center Troubleshooting If there is low or no bass outputStaple sales invoice here

PS1400 specifications

The JBL PS1400 is a powerful and versatile speaker that caters to a wide range of audio needs, making it an excellent choice for both professional and casual use. Known for its robust build and exceptional sound quality, the PS1400 stands out in the competitive audio landscape.

One of the primary features of the JBL PS1400 is its impressive power handling capability. With a rated power output of 1400 watts, this speaker can easily fill large venues with clear, vibrant sound. The speaker is designed to handle high levels of audio without distortion, ensuring that music and vocal performances sound crisp and dynamic, even at high volumes.

The PS1400 utilizes JBL's advanced transducer technology, which enhances its sound reproduction. The speaker features a high-frequency compression driver that delivers pristine treble frequencies, providing clarity and detail that can be heard even in challenging acoustic environments. Additionally, the 14-inch woofer is engineered to produce rich bass tones, offering a well-balanced audio experience across the frequency spectrum. This dual driver setup allows for an impressive sound stage, making it suitable for live events, DJ performances, and studio monitoring.

Another notable aspect of the JBL PS1400 is its durable design. Built with high-quality materials, the speaker is engineered to withstand the rigors of both indoor and outdoor use. Its rugged enclosure protects against damage from physical impact and environmental conditions, while the integrated handles facilitate easy transport. Coupled with its professional-grade connectors, the PS1400 is designed for reliability in various settings.

In terms of connectivity, the JBL PS1400 features versatile input options, including XLR and TRS connectors, allowing seamless integration with different sound systems and equipment. This flexibility makes it ideal for use in diverse situations, from concerts to corporate events.

Overall, the JBL PS1400 combines power, quality, and durability, making it an exceptional choice for anyone looking to enhance their audio experience. With its advanced technologies and robust features, the PS1400 delivers a sound quality that is hard to match, ensuring that your music sounds its best, whether on stage or in the studio.
Top Page Image Contents