JBL S36AWII, S36II manual E a K E R C O N N E C T I O N S, Troubleshooting

Page 3

Installation of Self-Adhesive

pads are required, and they

or any non-JBL brackets or

Rubber Pads: If the speaker is to

need to be installed on the back

accessories to these threads, as

be placed on a surface (such as

of the loudspeaker, near the

this might damage the speaker

a table top or shelf) rather than

lower edge, so that they are

and dislodge the insert.

wall-mounted, the enclosed self-

located between the S36AWII

 

adhesive rubber pads are to be

back and the mounting surface.

 

attached to the bottom of the

Please see the enclosed

 

installation template for more

 

speaker cabinet in their

 

details.

 

designated recessed locations.

 

NOTE: The threaded inserts on

 

If the speaker is to be wall-

PADS GO HERE

mounted, then the four self-

the bottom of the speakers are

For tabletop or shelf placement

adhesive rubber pads should be

to be used only with JBL

PLACE RUBBER PADS HERE

attached to the back of the

accessories that have been

 

speaker, as shown in the bottom

developed specifically for the

 

right diagram.

S36 and that may become

 

When angle-mounting the

available at a future date.

KEYHOLES FOR

S36AWII, only two of the rubber

Do not attempt to install bolts

MOUNTING HARDWARE

For wall-mounting

 

 

S P E A K E R C O N N E C T I O N S

CONNECTION TIPS

Speakers and electronics terminals have corresponding (+) and (–) terminals. It is important to connect both speakers identically: (+) on the speaker to

(+) on the amplifier and (–) on the

speaker to (–) on the amplifier. Wiring “out of phase” results in thin sound, weak bass and a poor stereo image. With the advent of multichannel surround sound systems, connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material.

To use the binding-post speaker terminals, unscrew the collar until the pass-through hole in the center post is visible under

RIGHT

LEFT

– +

– +

– +

– +

Speaker Outputs

the collar. Insert the bare end of the wire through this hole; then screw the collar down until the connection is tight. The hole in the center of each collar is intended for use with banana- type connectors.

T R O U B L E S H O O T I N G

If there is no sound from any of the speakers:

•Check that receiver/amplifier is on and that a source is playing.

•Review proper operation of your receiver/amplifier.

•Make sure all wires are connected. Make sure none

of the speaker wires are frayed, cut or punctured.

If the system plays at low volumes but shuts off as volume is increased:

•Check all wires and con- nections between receiver/ amplifier and speakers.

•Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured.

•If more than one pair of main speakers is being used, check the minimum impedance

requirements of your receiver/ amplifier.

If there is no sound coming from one speaker:

•Check the “Balance” control on your receiver/amplifier.

•Check all wires and connec- tions between receiver/amplifier and speakers. Make sure no wires are touching other wires or terminals and creating a short circuit.

•Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured.

•In Dolby* Digital or DTS® mode, make sure that the receiver/ processor is configured so that the speaker in question is enabled.

•Turn off all electronics and switch the speaker in question with one of the other speakers

that is working correctly. Turn everything back on, and determine whether the problem is in the same place, i.e., the speaker that was working previously now has no sound and the speaker that was not working now sounds fine; or whether it has moved, i.e., the speaker that was not working still has no sound and the speaker that was working is still fine. If the problem is in the same place, the source of the problem is most likely with your receiver or amplifier, and you should consult the owner’s manual for that product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit our Web site at www.jbl.com for further information.

Page 2 Page 4
Image 3
Page 2 Page 4
Contents S36II, S36AWII On a ceiling, on For stereo-only applicationsFor home theater applications Attempt to mount theseE a K E R C O N N E C T I O N S TroubleshootingSpecification S Maximum RecommendedCrossover Frequencies

S36AWII, S36II specifications

The JBL S36II and S36AWII are notable entries in JBL's line of high-performance loudspeakers, designed to elevate the audio experience in both home and outdoor environments. Renowned for their impressive sound reproduction and robust build quality, these speakers are tailored for audiophiles and casual listeners alike.

The JBL S36II is equipped with advanced technologies that ensure clear, dynamic sound across a range of frequencies. One of its standout features is the 6.5-inch woofer, which provides deep, rich bass response while maintaining clarity in higher frequencies. This woofer is complemented by a 1-inch soft-dome tweeter that delivers crisp high notes and enhances the overall soundstage, resulting in an immersive audio experience whether you're listening to music, watching movies, or gaming.

The design of the S36II emphasizes both aesthetics and functionality. Its sleek cabinet construction minimizes resonance, ensuring that audio playback remains pure and true to the original recording. The elegant finish allows it to blend seamlessly into any room decor, whether in a dedicated home theater setup or as part of a stereo system.

On the other hand, the JBL S36AWII is specifically designed for outdoor use, offering similar acoustic features while boasting enhanced weather resistance. The rugged enclosure protects the speaker from environmental elements, making it suitable for patios, gardens, and poolside areas. Its UV-resistant materials ensure longevity and performance even under direct sunlight.

Both models feature JBL's proprietary technology, such as the Image Control Waveguide, which helps optimize the stereo imaging and creates a broad soundstage. This technology aids in delivering consistent sound, regardless of your listening position in the room or outdoor space. The integration of advanced crossover components ensures that the speakers efficiently manage the distribution of frequencies, resulting in a balanced sound output.

In summary, the JBL S36II and S36AWII embody the brand's commitment to high-quality audio, marrying innovative technologies with superior craftsmanship. Whether indoors or outdoors, these speakers provide an exceptional audio experience, making them ideal choices for music enthusiasts and home entertainment aficionados seeking both quality and durability.
Top Page Image Contents