Smeg SNZ414IS, SNZ414S instruction manual Installation and hook-up, Water supply connection

Page 6

Installation instructions

2. Installation and hook-up

Remove the polystyrene basket retainers.

Position the appliance in the desired place of installation. The back or sides of the dishwasher may be placed up against walls or other furniture units. If the dishwasher is installed near a heat source, fit the special insulating panel to prevent overheating and malfunction of the appliance. To ensure stability, install integrated or built-under dishwashers only under continuous worktops, and screw them to the adjacent units. To facilitate the installation procedure, the intake and drain hoses can be positioned in any direction; make sure that the hoses are not kinked, crushed or pulled too tightly. Make sure to tighten the locking ring-nut once the pipes have been placed in the direction required. A hole at least 8 cm in diameter is required to allow the power supply cable and pipes to pass.

Level the appliance on the floor using its adjustable feet. This operation is essential for ensuring correct operation of the dishwasher.

Installing a hob on top of a free-standing dishwasher is absolutely forbidden. Building-in a dishwasher underneath a ceramic hob is absolutely forbidden.

A dishwasher can be built-in underneath a conventional hob provided there is no break in the kitchen worktop, and the dishwasher and hob are installed and secured correctly, so that no hazards are generated.

For free-standing models only: if the appliance is not built-in and is therefore accessible on one side, the door hinge area must be covered for safety reasons (injury hazard).

The covering fixtures are available as an accessory from specialist dealers or the After-Sales Service.

To build in the dishwasher, the special kit must be purchased from authorised dealers or the After-Sales Service.

Some models are equipped with only one adjustable foot at the rear, which can be adjusted by turning the screw on the lower front part of the appliance.

2.1 Water supply connection

Preventing the risk of clogging or damage: if the water pipe is new or has not been used for a long time, before connecting to the water supply check that the water is clear and free of impurities, to prevent damage to the appliance. The dishwasher must always be connected to the water system with new hoses; old or used hoses must never be reused.



Image 6
Contents Dishwasher Contents Safety instructions Safety and operating instructionsSafety instructions Aquastop Models Installation and hook-up Water supply connectionConnecting to the Water Supply Drain ConnectionElectrical connection and precautions When Cleaning and Maintaining the ApplianceDescription of the controls Front panel11,5 Table for Certification Bodies Normal ECOWashing programs LightingProgramming Start ProgramEND Program Interruption of a ProgramTo Change a Program Delay Program Annulling a ProgramUser instructions To Save on ENERGY! … and Protect the Environment Removing the DishesUsing the rinse aid and detergent dispensers Operating instructionsAdding the Rinse AID Adjusting the Rinse AID Dispenser Setting Adding the DetergentUser instructions General warnings and recommendations User instructions Using the baskets Lower BasketLoading the Lower Basket Cutlery Basket Upper BasketAdjusting the Upper Basket Loading the Upper BasketCleaning and maintenance Cleaning the Water Intake FilterCleaning the Spray Arms Cleaning the Spray ARM, Travelling Version Cleaning the Filter UnitGeneral Warnings and Recommendations for Correct Maintenance If the dishes are not being cleaned properly, check that Troubleshooting Code Phases Lights DescriptionTechnical Data 115 125 135 145 155

SNZ414S, SNZ414IS specifications

The Smeg SNZ414IS and SNZ414S are innovative and stylish kitchen appliances designed to enhance every cooking experience. Known for their distinct Italian design and advanced technology, these models stand out in the competitive landscape of built-in ovens and multifunctional cookers.

One of the main features of the Smeg SNZ414IS and SNZ414S is their impressive energy efficiency. With an A+ energy rating, both models help users reduce energy consumption while maintaining excellent cooking performance. This not only translates to lower electricity bills but also reflects Smeg's commitment to environmentally friendly products.

Both variants come with multiple cooking functions, including conventional cooking, fan-assisted cooking, and grill options, allowing users to prepare a wide range of dishes. The intuitive control panel features easy-to-use knobs and digital displays, enabling precise adjustments for temperature and cooking times. The models also include a rapid preheat function, which significantly reduces waiting time before cooking starts.

The design of the Smeg SNZ414IS and SNZ414S is another notable characteristic. Featuring Smeg's iconic rounded aesthetic and chic stainless steel finish, these ovens are not just functional but also serve as a stylish addition to any kitchen décor. The visually appealing style is complemented by easy-to-clean surfaces, ensuring the ovens maintain their pristine appearance over time.

In terms of safety features, both models are equipped with a triple-glass door that minimizes heat loss while ensuring a safe cooking environment. Additionally, the cooling fan helps to maintain a safe external temperature, making these ovens suitable for families with children.

The interior of the Smeg SNZ414IS and SNZ414S is spacious and well-designed, allowing users to cook multiple dishes simultaneously. The oven cavity is also equipped with integrated lighting, providing excellent visibility of the cooking progress without the need to open the door.

Lastly, these ovens are compatible with Smeg's unique accessories, such as pizza stones and steam cooking trays, allowing for versatile cooking options. The Smeg SNZ414IS and SNZ414S not only meet the needs of passionate home cooks but also cater to those who prioritize style and energy efficiency in their kitchen appliances.