True Manufacturing Company T-23DT Electrical Instructions, Sealing Cabinet to Floor

Page 10

True Food Service Equipment, Inc.

INSTALLATION / OPERATION INSTRUCTIONS

ELECTRICAL INSTRUCTIONS

A.Before your new unit is connected to a power supply, check the incoming voltage with a voltmeter. If anything less than 100% of the rated voltage for operation is noted, correct immediately.

B.All units are equipped with a service cord, and must be powered at proper operating voltage at all times. Refer to cabinet data plate for this voltage.

TRUE requires that a sole use circuit be dedicated for the unit. Failure to do so voids warranty.

WARNING

Compressor warranties are void if compressor burns out due to low voltage.

WARNING

Power supply cord ground should not be removed!

NOTE

To reference wiring diagram - Remove front louvered grill, wiring diagram is positioned on the inside cabinet wall.

SEALING CABINET TO FLOOR

Step 1 - Position Cabinet

Allow one inch between the wall and rear of the refrigerator to assure proper ventilation. For freezers

3 inches between the wall and rear of the cabinet will assure proper ventilation.

Step 2 - Level Cabinet

Cabinet should be level, side to side and front to back. Place a carpenter’s level in the interior floor in four places:

A. Position level in the inside floor of the unit near the doors. (Level should be parallel to cabinet front). Level cabinet.

B. Position level at the inside rear of cabinet. (Again level should be placed parallel to cabinet back).

C. Perform similar procedures to steps a & b by placing the level on inside floor (left and right sides - parallel to the depth of the cooler). Level cabinet.

Step 3

Draw an outline on the base on the floor.

Step 4

Raise and block the front side of the cabinet.

Step 5

Apply a bead of “NSF Approved Sealant”, (see list below), To floor on half inch inside the outline drawn. The bead must be heavy enough to seal the entire cabinet surface when it is down on the sealant.

Step 6

Raise and block the rear of the cabinet

Step 7

Apply sealant on floor as outline in Step 5. on other

three sides.

Step 8

Examine to see that cabinet is sealed to floor around entire perimeter.

NOTE

Asphalt floors are very susceptible to chemical attack. A layer of tape on the floor prior to applyingthe sealant will protect the floor.

NSF Approved Sealants:

1.Minnesota Mining #ECU800 Caulk

2.Minnesota Mining #ECU2185 Caulk

3.Minnesota Mining #ECU1055 Bead

4.Minnesota Mining #ECU1202 Bead

5.Armstrong Cork - Rubber Caulk

6.Products Research Co. #5000 Rubber Caulk

7.G.E. Silicone Sealer

8.Dow Corning Silicone Sealer

8

www.truemfg.com

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Freezer / Refrigerator Swing Door True Food Service Equipment, Inc Safety Precautions Proper Disposal of the Freezer / Refrigerator USE of Extension CordsHOW to Connect Electricity Required Tools Installation / Operation Instructions OwnershipUncrating Locating LevelingInstallation of Castors or Optional Legs Conductors and Circuits Electrical Instructions Sealing Cabinet to FloorStartup Replacement PartsRecommendation Shelving Installation / Operation & Light Switch Location StepDanfoss Temperature Control Freezer Sequence of Operation True Food Service Equipment, Inc Turning on Power Turning OFF PowerChange CUT OUT Temperature CUT OUT TemperatureDefrost MAINTENANCE, Care & Cleaning Cleaning the Condenser Coil Required ToolsImportant Warranty Information Stainless Steel Equipment Care and Cleaning Interior Lights Light Bulb ReplacementIDL Integrated Door Lighting A. Warranty Information U.S.A & Canada only

T-23DT specifications

True Manufacturing Company has long been a trusted name in the refrigeration industry, known for its commitment to quality, durability, and innovation. One of the standout offerings in their product line is the True T-23DT, a versatile two-door refrigerator that caters to the needs of commercial kitchens, restaurants, and convenience stores.

The True T-23DT is designed with efficiency and performance in mind, boasting a sturdy construction that ensures longevity. The cabinet is made from high-quality stainless steel, offering not only an attractive appearance but also resistance to corrosion and easy cleaning. The interior features aluminum walls that facilitate optimal airflow and temperature retention, contributing to its reliable cooling performance.

One of the key features of the T-23DT is its state-of-the-art refrigeration system. It utilizes environmentally-friendly R290 hydrocarbon refrigerant, which not only helps reduce energy consumption but also supports superior temperature control. The refrigerator operates within a range of 33°F to 38°F, ensuring that perishable items are stored at safe temperatures. Additionally, the self-contained capillary tube system efficiently circulates refrigerant, resulting in minimal fluctuations in temperature.

The T-23DT also incorporates a digital temperature control system with an external display, allowing users to monitor and adjust settings with ease. The system includes an automatic defrost feature that reduces the risk of ice buildup, thus lowering maintenance needs and enhancing efficiency. True's commitment to user-friendly design is evident in the easy-to-use interface and the clear visibility of temperature readings.

Another notable characteristic of the True T-23DT is its spacious interior. With ample storage capacity, this refrigerator is equipped with heavy-duty, adjustable shelving that allows for customizable configurations to accommodate diverse items and inventory. The doors are designed to remain open beyond 90 degrees for easy access, while magnetic door gaskets ensure a secure seal that enhances energy efficiency.

For added convenience, the T-23DT features 20-gauge stainless steel shelves and LED interior lighting, which provides excellent visibility of stored products without generating excessive heat. The unit is also equipped with 4-inch casters for easy mobility, allowing for flexibility in layout and cleaning.

In summary, the True Manufacturing Company T-23DT is a robust, energy-efficient two-door refrigerator that integrates cutting-edge technology with user-friendly features. Its durability, spacious interior, and reliable performance make it an essential asset for any commercial kitchen looking to maintain food safety and quality. With True, businesses can trust they are investing in a product that will meet their refrigeration needs for years to come.
Top Page Image Contents