BMW BLUETOOTH WIRELESS HEADSET manual Pairing Headset to Your Phone

Patented Self-Adjusting Microphone

Microphone sensitivity automatically adjusts for you when you extend or retract the microphone.

Microphone	Microphone
Sensitivity	Position
Slightly Higher	Extended
Slightly Lower	Retracted

Turning Headset On/Off

To Turn the
Headset On
Press and hold the On/Off
switch for 2 seconds. If the
headset is already paired
to a mobile phone and the
phone is turned on, the
LED Indicator	Light	will
flash green	for	1.5
seconds and then every 5
seconds while on or in
standby mode. If headset
is not paired to a phone, it
			Figure 6
will go into pairing mode.

PLEASE NOTE: If your headset was previously paired, you may need to press the Answer/End button once.

To Turn the Headset Off

Press and hold the On/Off switch for 2 seconds. The LED Indicator Light will flash green for 1.5 seconds then power off.

SECTION 3: Pairing Headset to Your Phone

Before you begin using the headset, you must pair it to your mobile phone.

To Pair in Headset and/or Hands Free Mode

1.Activate the Bluetooth® function on your mobile phone or other device. Please refer to your phone’s owners manual for instructions.

2.To pair, simply power up the headset. Wait until the LED Indicator Light will flash red/green alternately. Once switched on, the device remains pairable for 3 minutes.

3.To force the headset into pairing mode, slide and hold the volume switch up or down for approximately 7 seconds until the LED Indicator Light flashes an alternating green and red. Headset is pairable for 2 minutes when forced into pairing mode. Make sure the headset and your mobile phone are close to each other while pairing. When the headset enters pairing mode, use your Bluetooth® mobile phone to find it.

4.Follow the Bluetooth® pairing/set-up instructions and screen prompts on your phone to pair it with the headset. Please refer to your phone’s owners manual or go to www.fellowes.com/bluetooth for links to popular phone manufacturers’ websites.

5.When prompted, enter the headset pin code: 0000. If desired, the pin code may be changed. Please

refer to your phone’s owners manual for instructions.

6.If pairing is successful, headset exits pairing mode and is ready for use. The headset LED Indicator Light will now flash green every few seconds.

7.To manually exit pairing mode, hold the volume switch up or down for 2 seconds until the LED Indicator Light stops flashing red/green.

PLEASE NOTE: If pairing does not work, wait 90 seconds, reset your phone or device to the beginning of the Bluetooth® pairing process and repeat steps 1-7. Once pairing is complete, your headset will work with your mobile phone any time both units are powered on and in close proximity to each other.

Pairing Profiles

The BlueVoice™ Headset supports both Hands-Free and Headset profiles. The headset will automatically select a profile to use with your paired device. It will first try to select Hands-Free mode if supported by your phone. Usually, mobile phones that support both modes will select Hands-Free mode.

PLEASE NOTE: Hands-Free mode offers added functionality (see your phone’s owners manual). Pairing in Hands-Free mode automatically pairs headset in Headset mode as well.

Master Connection

When the BlueVoice™ Headset is switched on, or the pairing button is pressed, the headset will try to pair to the last paired/used device for approximately 5

seconds. Due to the multi-pairing feature, if a connection failure occurs, the headset will try to connect to the next most frequently used device on its stored list of devices. The LED will indicate when connection succeeds. If the headset cannot find a device with which to connect, it will go into pairing mode.

SECTION 4: General Operation

Adjusting the Volume

To increase volume, slide volume switch upward for each higher volume level. To decrease volume, slide volume switch downward for each lower volume level. There are eight (8) separate volume levels. During volume adjustment, you will hear short high tones getting louder through the earpiece as the volume goes up and softer as the volume goes down.

Making and Receiving Calls

Once BlueVoice™ is paired with your mobile phone, you can make and receive calls using the headset as long as it is turned on and within range of your phone (up to 10m/30 ft.).

1.For Phones Without Voice-Dialing Capability: To make a call, dial the number using the phone keypad and speak to your party through the headset. When using the headset to receive calls, press the Answer/End button once to answer. To end a call, press the Answer/End button a second time.

5 6