Creda REFLECTION Conduit BOX to Mains Terminal Block, Final Installation, List of Loose Items

Page 31

INSTALLATION INSTRUCTIONS

Any spare cable must be coiled either behind the oven (not more than 30cm above the base of the oven recess) or pushed into the air gap below the oven after installation.

Where a hob is fitted adjacent to or above an oven a 30 amp or 45 amp double pole switch with a minimum contact clearance of 3mm should be used to feed both units via separate suitably rated cables.

Where a hob unit is fitted above the oven unit we recommend that 85oC High Temperature PVC with insulated 3 core flexible cord to table 15 of BS 6141:1991 with a conductor size of 2.5mm2 must be used to connect the hob to the control unit.

Where a hob unit is fitted adjacent to the oven unit, then 4mm2 twin and earth cable to BS 6004 is recommended to connect the hob unit to the control unit.

In all cases adhere to routing details (see fig. 5).

Your cooker should have been checked to ensure that the voltage corresponds with your supply voltage, this is stated on the rating plate which is located on the oven front frame (lower).

CONDUIT BOX TO MAINS TERMINAL BLOCK

(a)The oven unit should be placed on the floor on its carton base in front of the housing cabinet. The rear of the unit should be in line with the conduit box.

(b)Ensure there is sufficient cable for any future servicing.

(c)Remove the terminal cover. Prepare the cable, pass it through the cable entry hole in the oven rear panel and fit to terminal block. Secure the cable clamp and replace the terminal cover.

4.FINAL INSTALLATION

(a)Using a spirit level, check that the housing cabinet is level from side to side and from front to back in its installed position.

(b)Correct any unevenness by placing spacers under the bottom of the cabinet. Make sure that the cabinet rests firmly on the floor without rocking.

(c)Before the oven is fitted the cabinet must be firmly secured to the backing wall for stability.

(d)The oven unit should now be lifted (this requires two people) into the cabinet and pushed fully home.

(e)Finally the oven unit must be secured to the cabinet. Position the oven side trims equally about the cabinet sides. This should give an overlap of approx. 1.5mm per side (see Fig. 2). Secure the oven unit to the cabinet, through the side trims, by means of the four screws provided, two each side trim.

(f)Remove all packing material from the grill and oven interior.

LIST OF LOOSE ITEMS

4 x No.6 Pozi Head screws

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Instructions for Installation and Use Single Oven Creda Answer Centre 0541 54 64 Creda Answer Centre 0541 54 64Contents Introduction Safety Advice For Your SafetyAlways Disposal of Your Product NeverKnow Your Oven Control Markings Control PanelAutomatic Cooking Oven Timer OperationHints on Automatic Cooking Clockface Know Your TimerSymbols Timer Function ButtonsSetting the Minute Minder Setting the Time of DAYAuto Cooking Programmes Electronic Clock & Automatic Oven Timer Operation Other Notes on Timer Operation Step Grill PAN & HandleGrill PAN Food Grid and ANTI-SPLASH Tray Door Position for GrillingGrilling Procedure Food Heat Guide to Grilling SuccessfullyOven Shelf Positioning for FAN Oven Temperature & TimeOven Utensils FAN Oven Operation Operation Slow SettingPoints to Consider When Preparing Food for Slow Cooking Advantages of Slow Cooking areConvection Fan Temperature Conversion ScaleOven If Using Aluminium Foil Oven Temperature Charts MeatOven Temperature Charts Baking Baking General GrillCleaning Care and CleaningCredaclean Oven Liners How Credaclean worksRemovable Grill Roof Panel not all models Cleaning the OvenBase of Main Oven Grill/Meat Pan & Oven ShelvesHOW to Clean the Lamp Lens Replacement of the Oven LampControl Panel / Trims / Inner Door Panel & Glass Cleaning the Doors General Installation InstructionsElectrical Installation Oven Unit Housing CabinetsMains Supply All cases adhere to routing details see fig Final InstallationConduit BOX to Mains Terminal Block List of Loose Items560mm 550mm Something WRONG? Problem CheckPage Key Contacts

REFLECTION specifications

Creda REFLECTION is an innovative heating solution designed to revolutionize the way we experience warmth and comfort in our homes. This advanced system combines modern technology with elegant design, making it a popular choice for homeowners who value both aesthetics and efficiency.

One of the standout features of the Creda REFLECTION is its sleek, minimalist appearance. With a frameless glass front that reflects its surroundings, it blends seamlessly into any interior decor. This design not only adds a touch of sophistication but also allows for flexible placement options, making it suitable for various rooms, including living rooms, bedrooms, and bathrooms.

In terms of technology, the Creda REFLECTION employs advanced infrared heating. Infrared heaters work by emitting heat directly to objects and surfaces in the room, rather than warming the air. This method offers several benefits, including quicker heat-up times and improved energy efficiency. Since infrared heating is more direct, it can provide a comfortable thermal environment while consuming less energy compared to conventional heating methods.

Another significant advantage of the Creda REFLECTION is its programmable thermostat. Users can easily set their preferred heating schedules, allowing them to control energy consumption and costs effectively. The ability to program the unit to heat only when needed not only enhances comfort but also helps in reducing carbon footprints.

Safety is a crucial consideration in the design of the Creda REFLECTION. The unit features overheat protection and a child lock function, ensuring peace of mind for families with young children. Additionally, the glass front remains relatively cool to the touch during operation, reducing the risk of burns.

Installation and maintenance are also user-friendly. The Creda REFLECTION can be mounted on walls with ease, making it a practical choice for both new builds and renovations. Maintenance requirements are minimal, as the unit does not have moving parts or require filters, ensuring long-term reliability.

In summary, the Creda REFLECTION stands out as a high-quality and stylish heating solution. With its sleek design, efficient infrared technology, programmable features, and safety considerations, it caters to the needs of modern households looking for both comfort and energy efficiency. Ideal for a variety of settings, it represents a smart investment for those aiming to enhance their living spaces with innovative heating solutions.
Top Page Image Contents