GAS Equipment Assembly, Electric Equipment

GAS EQUIPMENT ASSEMBLY

SOLENOID VALVE .

INLET FITTING

MANUAL SHUTOFF VALVE .

Shown in open position

PRESSURE TEST PORT .

FIG. 12

BURNER JET .

ELECTRIC EQUIPMENT

HEATER

The heat necessary for the operation of an absorption cooling unit is supplied by an electric heater mounted in a pocket of the boiler system.

This model is equipped with one electric heater for 120 volt AC.

To replace the heater proceed as follows:

1.Disconnect the wall plug, and the 12 volt wires.

2.Remove the power module cover see FIG. 1.

3.Disconnect the heater leads.

4.With a pair of pliers unfold the lug holding the lid of the boiler casing and open the lid.

5.Remove some insulation wool so that the heater is accessible.

6.Turn and lift the heater out of its pocket.

7.Fit the new heater into the pocket.

8.Connect the leads and put on the power module cover.

9.Reset the insulation and close the lid of the boiler.

FUSES

This model is equipped with 2 fuses, one for the refrig- erator control system and one for the AC heater.

(See table below).

To replace fuse(s) proceed as follows.

1.Disconnect the wall plug, and the 12 volt wires.

2.Remove the power module cover. See FIG. 1.

3.Snap the fuse out of the fuse holder.

4.Fit a new fuse in to the fuse holder.

5.Replace the power module cover.

Control system	3 Amp
AC heater	5 Amp

NUT

THERMOCOUPLE

SPARK ELECTRODE

BURNER TUBE

BURNER MOUNTING SCREW

MAINTENANCE & SERVICE

The user should be aware of service that must be done on a regular schedule to keep the refrigerator operating properly. The service should only be per- formed by a qualified technician who is familiar with LP gas systems and refrigerators.

1. REFRIGERATOR REMOVAL

Before working on the refrigerator, make sure the AC voltage and DC voltage leads are disconnected. Shut off the gas supply at the LP tank. Disconnect the gas supply line at the rear of the refrigerator, see FIG. 1. Always use a back up wrench when loosening and tight- ening connections.

Cap the gas supply line, loosen the screws anchoring the refrigerator to the enclosure and slide the refrigera- tor out of the compartment.

When replacing the refrigerator make sure that the seal- ing strips are properly positioned.

Replacement is the reverse of removal. Check all con- nections for gas leaks.

Refer to section INSTALLATION, page 4 to 8.

2. PERIODIC MAINTENANCE

To keep your Dometic refrigerator operating efficiently and safely, periodic inspection and cleaning of several components once or twice a year is recommended.

A. It is important to keep the area at the back of the refrigerator clean. Check the lower vent, upper vent and area between these openings for any obstruc- tions such as bird/insect nests, spider webs, etc. Clean the coils on the back of the refrigerator. Use a soft bristled brush to dust off the coils.

It is important to keep the refrigerator area free from combustible material, gasoline and other flammable vapors or liquids.

NOTE: The following maintenance is required once or twice a year, but should only be done by a qualified ser- viceman who is familiar with LP gas systems and refrig- erators.

NDR1062 specifications

The Dometic NDR1062 is a highly versatile and efficient refrigerator designed for use in RVs, boats, and other mobile applications. This model caters specifically to travelers who require reliable and effective cooling solutions while on the go.

One of the standout features of the Dometic NDR1062 is its dual power option. It can operate on both 12/24V DC and 110-240V AC, making it adaptable for various environments and power sources. This flexibility allows users to connect the refrigerator to their vehicle’s battery during travel and switch to shore power when parked.

The refrigerator offers spacious storage, with a total capacity of 106 liters. This ample space is ideal for storing food and beverages, accommodating the needs of families or groups on extended trips. Additionally, the fridge is equipped with adjustable shelves, allowing users to customize the interior layout as per their requirements.

Dometic's absorption technology is another key characteristic of the NDR1062. This silent operation system uses a chemical process to move heat away from the fridge interior, ensuring quiet cooling without the noise typically associated with compressor units. As a result, the Dometic NDR1062 is perfect for use in locations where noise is a concern, such as campgrounds or while sleeping in the vehicle.

The design of the Dometic NDR1062 also emphasizes user convenience. The refrigerator features an easy-to-read LED display that provides real-time information about the internal temperature, allowing for precise adjustment to ensure optimal food preservation. Moreover, its sleek, compact design ensures that it can fit seamlessly into various spaces while still offering easy access to contents.

Durability is another crucial aspect of the Dometic NDR1062. Built with high-quality materials, it is designed to withstand the rigors of mobile living, including bumps and vibrations common during travel. The robust construction means that it can handle the demands of outdoor adventures without compromising performance.

In summary, the Dometic NDR1062 stands out as a reliable and efficient cooling solution for anyone needing refrigeration on the road. Its dual power option, spacious storage, low-noise operation, and robust durability make it an excellent choice for those seeking an effective mobile refrigerator. With its thoughtful design and user-friendly features, the NDR1062 is a valuable addition to any traveling setup.