Dometic RM7030 GAS Flame Warning Lamp, Delay Mode Lamp and Switch, GAS Mode Lamp and Switch

Page 17
7 Pin
10 Pin
YELLOW
BROWN

DOMETIC® RM7030/RM7732 Refrigerators

DIAGNOSTIC SERVICE MANUAL

With the mode switch (?) NOT depressed: A reading wouldNOT be indicated.

NOTE: If the check on AC mode lamp and switch is not correct, verify the wire harness has continuity. If wire harness is good, replace the upper circuit

I. GAS FLAME WARNING LAMP:

NOTE: The following checks should be made on the upper circuit board and harness assemblyBEFORE replacing the upper circuit board or wiring harness. The checks are to be done with the wiring harnessREMOVED from the lower circuit

board.

board, and the OFF-ON switch turned to

BLACK

G.DELAY MODE LAMP AND SWITCH

"ON".

BROWN

NOTE: The following checks should be made on the upper circuit board and harness assemblyBEFORE replacing the upper circuit board or wiring harness. The checks are to be done with the wiring harness REMOVED from the lower circuit board, and the OFF-ON switch turned to "ON".

With the mode switch (?) manually depressed: Resistance should be indicated between the brown terminal on the 10-pin connector (negative [–] lead from meter) to the yellow terminal on the 7-pin connector (positive [+] lead from meter). The proper resistance is approximately

26,000 ohms.

With the mode switch (?) NOT depressed: A reading would NOT

be indicated.

NOTE: If the check on the delay mode lamp and switch is not

correct, verify the wire harness

has continuity. If wire harness is good, replace the upper circuit board.

H.GAS MODE LAMP AND SWITCH:

NOTE: The following checks should be made on the upper circuit board and harness assemblyBEFORE replacing the upper circuit board or wiring harness. The checks are to be done with the wiring harness REMOVED from the lower circuit board, and the ON- OFF switch turned to "ON".

With the mode switch (?) manually depressed:

Resistance should be indicated between the brown

terminal on the 10-pin connector (negative [–] lead

from meter) to the green terminal

 

 

on the 7-pin connector (positive [+]

GREEN

BROWN

lead from meter). The proper

 

 

resistance is approximately 26,000

 

 

ohms.

 

 

With the mode switch (?) NOT

 

 

depressed: A reading would NOT

7 Pin

10 Pin

be indicated.

NOTE: If the check on gas mode lamp and switch is not correct, verify the wire harness has continuity. If wire harness is good, replace the upper circuit board.

Measure resistance between the brown terminal on the 10-pin connector (negative

[–]lead from meter) to the black terminal on the 10-pin connector (positive [+] lead from

meter). The proper resistance is approxi-

10 Pin

mately 22,000 ohms.

 

NOTE: If the check on gas flame warning lamp is not correct, verify the wire harness has continuity. If wire harness is good, replace the upper circuit board.

J.RM7030 (Product No. 921890401) and RM7732 NOTE: The PAL tester will allow for proper testing of the integrity of the upper and lower circuit boards. PAL is available from your Dometic parts distributor.

NOTE: Each of the following tests should be done according to pin locations. The wire colors may vary.

With main ON/OFF switch on display panel in OFF position:

Check for DC voltage at Plug 1, Terminal 4 and terminal 5 negative (–) DC on the lower circuit board. If no voltage, then check fuse condition. Replace if blown. Check for DC voltage between J4 and J10 terminals on the lower circuit board. If fuse is good and there is battery voltage at J4, remove and replace lower circuit board.

Next, check for DC voltage at the upper circuit board between terminal 4 (orange or white wire) and terminal

3(black wire) which is negative (–) DC. If no voltage, and your previous check proved voltage at the lower circuit board between these wires, replace the cable assembly. If DC volts are present, proceed to the next check.

UPPER CIRCUIT BOARD

14

Image 17
Contents Foreword Contents Other WiringICE Maker ICE Maker ComponentsRM7030 Refrigerator Section Symptom Cause Refer to Step Refrigerator SectionC,D Symptom Cause Refer to StepSymptom Cause Refer to Step ICE Maker Section LP GAS Delay Mode AES Fully Automatic ModeOperation LP GAS OperationFlame Failure During LP GAS Operation AES Display Panel AES Mode Volts AC OperationLOW Voltage Monitor ThermostatStandby Mode of Operation GAS ModeAuto Mode RM7732 Refrigerator OperationTo Shut OFF the Refrigerator Description of Operating ModesAccomponents Heating Element AC Voltage RequirementsDC Voltage Requirements DC ComponentsSolenoid Valve Thermistor AdjusterThermistor High Voltage Cable IgniterUpper Circuit Board ON-OFF SwitchFuses AC Mode Lamp and Switch AES Function SwitchGAS Function Lamp AES Function LampGAS Flame Warning Lamp Delay Mode Lamp and SwitchGAS Mode Lamp and Switch Lower Circuit Board Diagnostic ModeRM7030 Product No & RM7732 Door Switch Electrode LP GAS RequirementsClimate Control Heater Test PortManual GAS LP GAS ComponentsThermocouple OrificeInternal Wiring WiringBurner Flue BaffleTypical Wiring Diagram for Volts AC RM7732 Typical Wiring Diagram Other Securing the Refrigerator Door Position Ambient TemperatureSmooth FIT, Proper Seal Cooling UnitInterior Liner Seal to Frame ICE Maker Components ICE Maker OperationMold Heater ICE EjectorShutoff ARM Mold SwitchesTiming Motor Water ValveICE Maker Assembly Schematics on Pages 32 ThroughDometic RM7030/RM7732 Refrigerators Dometic RM7030/RM7732 Refrigerators ICE Maker Other Water Fill AdjustmentWater Supply ICE Maker Typical Wiring Diagram

RM7030, RM7732 specifications

The Dometic RM7732 and RM7030 are two innovative refrigeration solutions designed for those who enjoy outdoor adventures such as camping, RVing, and boating. These refrigerators are engineered to provide reliable cooling performance while prioritizing energy efficiency and ease of use.

The Dometic RM7732 is a three-way refrigerator that operates on 12V DC, 110V AC, and propane. Its versatility makes it an ideal choice for those who may not always have access to an electric power source. With a capacity of 7.3 cubic feet, it can hold a substantial amount of food and beverages, making it perfect for extended trips. The RM7732 also boasts an impressive temperature range, allowing it to maintain optimal cooling conditions even in varying outdoor temperatures. Its sleek design includes a reversible door, providing flexibility in installation and use.

On the other hand, the Dometic RM7030 is a double-door refrigerator that combines style with functionality. This model also supports three-way operation: propane, 12V DC, and 110V AC. It offers a slightly smaller capacity than the RM7732 but is still equipped to handle the needs of a small family or group. One of its standout features is its efficient absorption cooling technology, which ensures that the refrigerator operates quietly, making it an excellent choice for nighttime use.

Both models feature an electronic ignition system that simplifies the process of starting the propane function. The intuitive control panel on each unit allows users to easily select the preferred power source and adjust the temperature settings. Energy-efficient LED lighting inside the refrigerators enhances visibility while consuming minimal power.

Dometic has incorporated advanced insulation materials in both the RM7732 and RM7030 to reduce energy consumption, ensuring that food stays cooled even under high ambient temperatures. The sturdy construction is designed to withstand the rigors of outdoor use, and the units are built to last.

In summary, the Dometic RM7732 and RM7030 refrigerators are excellent choices for outdoor enthusiasts seeking reliable, versatile, and energy-efficient cooling solutions. With their range of power options, impressive capacities, and user-friendly features, they are well-equipped to handle the demands of any adventure while keeping your provisions fresh and cool.