Whirlpool CEX630V Caring For Your Cooktop, Control panel, Surface units and reflector bowls

Griddle		chart
Preheat	griddle for 10 mini		2s on HI.
FOOD			CONTROL SETTING
Sausage	patties		5
Bacon slices			HI
Ham slice		(3/4”)	6
Hamburgers			6
Hot dogs			6
French	toast		6
Grilled	sandwiches		6
Pancakes			6
Fried eggs			HI

FIRST SIDE		SECOND SIDE
9 min.		5 min.
6 min.		2 min.
6 min.		6 min.
8 min.		8 min.
8 min.(turn often)
3 mm.		2 mm.
3 l/2	min.	3 min.
2 mm.		2 min.
3/4	1 min.	l/2 min.

COMMENTS

Grease griddle with oil, If desired.

Grease griddle with oil, if desired.

tiriddlmg and grilling times are approximate and may neea to De aalustea to maiviauat tastes.

Caring For Your Cooktop

Burn And Electrical Shock Hazard

Make sure all controls are OFF and the cooktop is cool before cleaning. Failure to do so can result in burns or electrical shock.

Solid element surface units (Model CEX215V)

The control knobs

1.Turn control knobs to the OFF position.

2.Pull knobs straight off.

3.Wash in warm, soapy water.

4.Rinse well and dry completely. Do not soak.

The control panel

1.Wipe with warm, soapy water or spray glass cleaner, and soft cloth.

2.Rinse well.

3.Dry with soft cloth.

4.Replace control knobs by pushing them firmly into place.

NOTE: Make sure all control knobs point to the OFF position.

When cleaning, never use steel wool, abrasives, or commercial oven cleaners which may damage finish.

Surface units and reflector bowls

Removing

3.Lift out the reflector bowl. See Cleaning Chart on page 6 for cleaning instructions.

Replacing

1.Line up openings in the reflector bowl with the surface unit receptacle.

2.Hold the surface unit as level as possible with the terminal just started into the receptacle. Push the surface unit terminal into the receptacle.

3.When the terminal is pushed into the receptacle as far as it will go, the surface unit will fit into the reflector bowl.

Reflector bowls reflect heat back to the utensils on the surface units. They also help catch spills. When they are kept clean, they reflect heat better and look new longer.

If a reflector bowl gets discolored, some of the utensils may not be flat enough, or some may be too large for the surface unit. In either case, some of the heat that’s meant to go into or around a utensil goes down and heats the reflector bowl. This extra heat can discolor it.

1.For best results, wipe off surface units with a damp soft cloth and soapy water after each use.

Burned-on food may be removed with a soapy scouring pad. The red spot in the center of the surface unit will gradually wash off. This is normal and will not affect the operation of the surface unit.

2.IMPORTANT: After cleaning, apply a thin coat of salt-free oil to the COOL surface units, then heat 3 - 5 minutes. It may still smoke slightly when heated. If surface units have dark spots caused by grease and food, the oil treatment will improve their appearance but not eliminate the spots.

NOTE: Optional Electrop dressing can be applied to the surface units to improve their appearance.

3.The stainless steel trim rings will yellow from the heat of the surface units and pans. This is normal. The yellowing can be removed by using stainless steel cleaner or Cook Top Polishing Creme on the trim rings.

To obtain order information for Cook Top Polishing Creme (Part No. 814009) or ElectrolE dressing (Part No. 814030), write to:

1.	Lift	the edge of the		unit opposite		Fire		And	Electrical	Shock	Hazard
	the	receptacle, just		enough	to clear
	the	reflector bowl.				Do	not	line	the reflector bowls with
2.	Pull	the	surface unit	straight	away	foil.	Fire or electrical			shock	could
	from the		receptacle.			result.

Whirlpool Corporation

Attention: Customer Service

Dept.

1900 Whirlpool Drive

LaPor-teJN 46305

Page 5