Whirlpool FEP310KN1 manual Oven USE

Home Canning

When canning for long periods, alternate the use of surface cooking areas, elements or surface burners between batches. This allows time for the most recently used areas to cool.

■Center the canner on the grate or largest surface cooking area or element. Canners should not extend more than 1" (2.5 cm) outside the cooking area.

■Do not place canner on 2 surface cooking areas, elements or surface burners at the same time.

■On ceramic glass models, use only flat-bottomed canners.

■On coil element models, the installation of a Canning Unit Kit is recommended. If a kit is not installed, the life of the coil element will be shortened. See “Assistance or Service” for ordering instructions.

■For more information, contact your local U.S. Government Agricultural Department Extension Office. Companies that manufacture home canning products can also offer assistance.

Cookware

IMPORTANT: Do not leave empty cookware on a hot surface cooking area, element or surface burner.

Ideal cookware should have a flat bottom, straight sides and a well-fitting lid, and the material should be of medium-to-heavy thickness.

Rough finishes may scratch the cooktop. Aluminum and copper may be used as a core or base in cookware. However, when used as a base they can leave permanent marks on the cooktop or grates.

Cookware material is a factor in how quickly and evenly heat is transferred, which affects cooking results. A nonstick finish has the same characteristics as its base material. For example, aluminum cookware with a nonstick finish will take on the properties of aluminum.

Cookware with nonstick surfaces should not be used under the broiler.

Use the following chart as a guide for cookware material characteristics.

COOKWARE	CHARACTERISTICS
Aluminum	■ Heats quickly and evenly.
	■ Suitable for all types of cooking.
	■ Medium or heavy thickness is best for
		most cooking tasks.
Cast iron	■ Heats slowly and evenly.
	■ Good for browning and frying.
	■ Maintains heat for slow cooking.
Ceramic or	■	Follow manufacturer’s instructions.
Ceramic glass	■ Heats slowly, but unevenly.
	■ Ideal results on low to medium heat
		settings.
Copper	■ Heats very quickly and evenly.
Earthenware	■	Follow manufacturer’s instructions.
	■ Use on low heat settings.
Porcelain	■ See stainless steel or cast iron.
enamel-on-
steel or cast
iron
Stainless steel	■ Heats quickly, but unevenly.
	■ A core or base of aluminum or copper
		on stainless steel provides even
		heating.

OVEN USE

Odors and smoke are normal when the oven is used the first few times, or when it is heavily soiled.

IMPORTANT: The health of some birds is extremely sensitive to the fumes given off. Exposure to the fumes may result in death to certain birds. Always move birds to another closed and well- ventilated room.

Electronic Clock/Timer

(on some models)

ABC

D		E
A. Timer	C. Increase	E. Decrease
B. Display	D. Clock

Display

When power is first supplied to the appliance, everything on the display will light up for 5 seconds. Then, the time of day and “PF” will appear on the display.

If “PF” appears at any other time, a power failure has occurred. Reset the clock. See “Clock” section.

When the oven is not in use, the display will show the time of day.

Clock

This is a 12-hour clock and does not show a.m. or p.m.

To Set:

Before setting, make sure the oven and Timer are off.

1.Press CLOCK.

The colon will flash during Clock programming.

2.Press the “up” or “down” arrow pads to set the time of day.

The time can be changed in either small or 10-minute increments by pressing a pad briefly or by pressing and holding a pad.

3.Press CLOCK. The colon will stop flashing when the Clock is active.

7