1.DISPLAY PANEL
| different modes and functions. | With | the | |
2. | PARAMETER | |||
| Parameter | |||
| time. |
| With | the |
3. | PARAMETER | |||
4.SEARCH WHEEL This wheel has 4 forward and 4
reverse speed positions allowing you to quickly scan through tracks. The more you turn the wheel in either direction the faster you search.
5.TRACK BUTTON These buttons are used the
select a track. Tapping the button will forward/back skip to the next track, holding down the button will rapidly forward/back skip through the tracks.
6.IN BUTTON This function allows you to set a cue point without music interrupt. This button also sets the starting point of a seamless loop.
7.OUT BUTTON This button is used to set the ending point of a loop. A loop is started by pressing the IN button, pressing the OUT button set the loop ending point. The loop will continue to play until the OUT button is pressed once again.
8.RELOOP BUTTON If a seamless loop has been
made, but the CD player is not actively in seamless loop mode (a loop is not playing), pressing the RELOOP button will instantly reactivate the seamless loop mode. To exit loop, press the OUT button. LOOP and RELOOP will appear in the LCD display when the reloop function is available. During play mode, pressing the RELOOP button will instantly return play the last set point without interrupt of music.
9.BANK PROGRAM BUTTON
1.After any Bank has been memorized, press and hold down the BANK Prog. button for one second and +1 will appear on the LCD display; then now you can start press the BANK button to select the desired Banks for programming. And it will be saved in order up to 12 banks.
2.Press the BANK P button again to end programming. Ex. Press Bank Prog.(1sec.) àshow +1àpress bank1 àshow +2àpress bank3 àshow +3àpress bank2 àpress Bank Prog. to end
Bank Program will be bank1+bank3+bank2 in order.
3.To play Bank Program in the sampler mode, press BANK PROG. button to start playing the desired Banks in order. Ex. Sampler mode:
press Bank Prog. à play bank1+bank3+bank2 in order.
10.CUE BUTTON Pressing the CUE button during
playback immediately pauses playback and returns the track to the last set cue point. In pause mode and the CD is at the cue point, press the CUE button to provide cue monitor. The red CUE LED will light when the CD is at the cue point.
11. PLAY/PAUSE BUTTON Each press of the button
to change from play to pause or from pause to play. In skid mode, press this button to break or slow start.
12.SAMPLER BUTTON Press this button, then press
the desired BANK button to set the sampler mode. When sampler mode is set, the audio sample will play over the CD (if still playing). The audio sample can even play when there is no disc inside. There are two ways to adjust the sampler pitch, you can turn the TIME PARAMETER button, or press the TIME
PARAMETER button down, then rotate the JOG wheel. There are also two ways to adjust the sampler volume. You can turn the RATIO PARAMETER button, or press the RATIO PARAMETER button down, then rotate the JOG wheel. The sampler will play once or continuous depending on mode. Press sampler button once for continuous play and LED is lit (static); Press button again for single play and LED flashes. Press again to cancel the sampler function and the LED is off.
13.MEMORY BUTTON Press this button to set the memory mode, then press the desired BANK button to memorize the music from the last cue point. The music length to be memorized is determined by the length of BANK. When the memory mode is set, the MEMORY LED is lit. You can also memorize the BANKs, FX’ parameter, and the last play mode (i.e. time, single/continuous, pitch select, activated FX) by pressing the memory for 1 sec. To recall the BANKs just activate the memory mode before you load a new disc.
14.EJECT BUTTON Press this button to eject disc.
The disc will not eject unless the player is in Cue or Pause, this is to prevent accidentally ejecting the disc while in play mode.
15.4%,8%,16%,100% PITCH SELECT BUTTON Press the button in order to change pitch percentage
of 4%,8%,16%,100%.
16. KEY CORRCETION BUTTON This button is used to activate Key Correction via the pitch controls. Key Correction mode allows tempo change while maintaining the original key. When the Key Correction is selected, the LED above the KEY CORRECTION button glows red.
17.PITCH ON/OFF BUTTON – This button is used to turn the PITCH SLIDER function on and off.
18.BPM BUTTON
modes. Press the BPM button to toggle (change between) PITCH or BPM on the LCD display. Press down and hold the BPM button for 1 sec. to change the auto/manual BPM mode.
19.TAP BUTTON The TAP button is used to enter
the BPM manually. Tap this button to the beat of the music a few times (x4) to display the current BPM.
20.PITCH SLIDER This slider is used to adjust the
playback pitch percentage. The slider is a set adjustment and will remain set until the pitch slider is move or the pitch function has been turned off.
21.BANK BUTTONS Press the desired BANK button
when the MEMORY LED is lit will set the memory mode. The music from the cue point will be memorized to the flash. Press the desired BANK button when the SAMPLER LED is lit will set the sampler mode. The sampler length is determined by the smaller one of out point and bank length. Press the desired BANK button will return to the start point instantly. The LED of the BANK button last pressed will be flashing.
22.TIME BUTTON The TIME button will switch the time value described in the time meter between elapsed play time, track remaining time, and total remaining time.
23.SGL/CTN BUTTON This function allows you to
choose between single track play or continuous track
play (all tracks in order). | The desired pitch of CD |
24. PITCH |