Whirlpool 1997 "E service manual General, Removing the Microwave Oven & Cabinet

Page 12

GENERAL

REMOVING THE MICROWAVE OVEN & CABINET

WARNING

Personal Injury Hazard

Disconnect from the electrical supply be- fore servicing the unit. Failure to do so could result in death or electrical shock.

IMPORTANT NOTE: Most of the microwave components can be serviced without remov- ing the unit or its cabinet. They can be ac- cessed by removing the vent grille and the control panel. Before removing the unit or its cabinet, first check the procedure for the com- ponent you wish to service to see if it is neces- sary. If it is necessary to remove the unit and its cabinet to service a component, use the following procedure.

CAUTION: Because of the weight and size of the microwave oven, two people are required to safely move and install it. Failure to do so could result in personal injury.

1.Disconnect the electrical supply to the microwave oven.

2.Remove the six screws from the base plate and lower it, (see the illustration on the next page), then disconnect the cooktop light connector, and set the base plate aside.

3.Remove the lock pin and washer from the top of the microwave oven.

LOCK PIN &

WASHER

4.Support the front of the microwave oven and remove the two bolts and washers from the top of the oven.

5.Using two people, remove the microwave oven from its mounting location and set it on a protected (padded) work surface.

6.To remove the vent grille from the micro- wave oven, remove the two inside screws from the top of the cabinet, then pull the top of the vent grille out so the two center tabs are free of their slots, and remove the grille.

7.Remove the screw from the power cord cover and remove the cover.

8.Remove the remaining screws from the top and rear of the cabinet.

9.Slide the cabinet back and unhook the sides from the tabs, then slide the power cord out of the cabinet, and remove the cabinet.

Proceed to the section for the component you wish to service.

2-2

Page 11 Page 13
Image 12
Page 11 Page 13
Contents OVER-THE-RANGE Microwave Oven Hood Combination MH7130XE MH7135XE MH9115XE Table of Contents Primary, Monitor, & Secondary Switch Checkout Procedure Important Safety Information Electrical Shock HazardPage Vii Leakage Test EquipmentTest Theory of Operation PK/WBL Component Access Component SectionsGeneral Removing the Microwave Oven & CabinetRemoving The Cabinet Protection Control System Removing the Oven DoorRemoving the Oven Door Components Removing the Control Panel Removing the Line Fuse REMOVING/ADJUSTING the Interlock Switches Removing a SwitchMaking Adjustments ALL Other Switches InsetRemoving the Base Thermal Fuse Control Panel OpeningRemove Five AIR Duct Screws Unplug Power Cord & FAN Motor Removing the Magnetron Thermal FuseRemoving the Convection Thermistor Remove Five Removing the Cavity Thermal Fuse Operating Control System Removing the Oven Light SocketControl Board Removing the FAN Motor Removing the Power Cord Removing the Blower Motor Capacitor Removing the Convection Heating Element Viewed from Under TOP Plate Removing the GAS Sensor Removing the Stirrer Motor Removing the Turntable Motor Removing the Cooktop Light Sockets Accessing the Components High Voltage ComponentsRemoving the Magnetron Removing the High Voltage Rectifier High Voltage Capacitor Removing the High Voltage Transformer Page Component Description & Testing Important Safety InstructionsPage Original March 4322167 Thermal Fuses Possible Customer ComplaintBlower Motor Capacitor GAS Sensor Convection Thermistor Convection Heating Element Viewed from Under TOP PlateMotors Programming Checks Touch Panel Continuity TestCharts Problem Possible Cause Test Procedure Or CorrectionProblem Possible Cause Test Procedure Or Correction Problem Possible Cause Test Procedure Or Correction Checking the Microwave Power Output Checking for Microwave Energy Leakage Measuring The Oven With The Cabinet Installed Making the MeasurementsOriginal March 4322167 Component Testing Test ChartsTerminal-To-Terminal Contacts Component Test Procedure Result Keyboard Matrix Control Circuit Board Check List Voltage circuitsPRIMARY, MONITOR, & Secondary Switch Checkout Procedure Continuity Test ChartDoor Open Door ClosedWiring Diagrams Tech TipsModel MH9115XE Strip Circuits Unit is Plugged in Clock is WorkingDoor is Open Oven Light is on Blower Motor is on LOWBlower Motor is on High Cooktop Lights are on High or LOWMicrowave Cooking is on Convection Cooking is onSpecifications Specification Charts MH7130XEQ MH7130XEZ MH7135XEBTemperature Sensor Probe Whirlpool Corporation MH7130XEQ MH7130XEZ MH7135XEB Beverage Frozen Entree MH7135XEQ MH9115XEB MH9115XEQ 120 Vertical CFM Hi/Low MH7135XEQ MH9115XEB MH9115XEQ Model & Serial Number Explanation Product IdentificationWhirlpool Microwave Hood Warranty Length of Warranty Whirlpool Will PAY for Will not PAY for

1997 "E specifications

The Whirlpool 1997 "E" is a notable refrigerator model that reflects the company's commitment to innovation and consumer convenience during the late 1990s. This model encapsulated both style and functionality, aiming to meet the evolving needs of households.

One of the standout features of the Whirlpool 1997 "E" is its Energy Saver technology. As energy efficiency became a paramount concern for consumers, this refrigerator was designed to minimize electricity consumption while maintaining optimal cooling performance. The appliance featured enhanced insulation and a high-efficiency compressor, allowing it to use less energy than many of its predecessors.

The design of the Whirlpool 1997 "E" was another highlight. It featured a sleek and modern aesthetic, available in several finishes including classic white, elegant black, and stainless steel. The exterior was complemented by smooth curves and a user-friendly interface, offering an appealing look that fit seamlessly into various kitchen decors.

Inside, the refrigerator came equipped with adjustable shelving and a spacious interior layout, allowing users to customize storage according to their needs. The easy-to-clean surfaces and removable shelves made maintenance simple, further enhancing the user experience. The model also included dedicated compartments for fruits and vegetables, with humidity controls to prolong freshness.

Another key technological advancement in the Whirlpool 1997 "E" was its advanced cooling system. Featuring MultiFlow technology, this model ensured a consistent temperature throughout the refrigerator and freezer compartments. This technology worked by circulating cold air across different shelves, minimizing temperature fluctuations that could affect food preservation.

The refrigerator also boasted features like a water filtration system, which improved the taste and quality of water dispensed through its integrated dispenser, providing convenience for families on the go.

Overall, the Whirlpool 1997 "E" set a benchmark for kitchen appliances in its era, combining energy efficiency, user-friendly design, and innovative technology. This model showcased Whirlpool's dedication to providing practical solutions that catered to the needs of contemporary households, making it a popular choice for many consumers. Its legacy continues to influence refrigerator designs in the years that followed, marking it as a significant player in the realm of home appliances.
Top Page Image Contents