Broan E60000 Series installation instructions Install the Hood, Connect the Wiring ALL Blowers

Page 11
WALL ANCHORS LOCATION

13. INSTALL THE HOOD

CAUTION

 

Hold the hood until it is completely secured to the wood

 

mounting strip.

 

INTERNAL BLOWER(S) ONLY

MOUNTING SCREWS LOCATION

 

Run power cable to installation location. Remove the electrical compartment cover.

 

Insert the cable in the hood and tighten the wire clamp to secure the cable.

 

ALL INSTALLATIONS

HD0264

 

Rest the back cavity of the hood on the wood mounting strip.

Secure the hood to wood mounting strip with (4) screws no. 8 x 3/4’’ (for 30’’ and

36’’ width hoods) or (6) screws (for 42’’ and 48’’ width hoods) provided at locations shown. Drill (3) 3/16’’ size holes into the drywall for wall anchors through the existing holes in the inside hood back in the locations shown. Then, install the three wall anchors with the remaining no. 8 x 3/4’’ screws and the (3) washers provided.

For a non-ducted installation, go to step 15, Connect the wiring.

14.ROUGH-IN PLATE LOCATION (EXTERNAL BLOWERS HOODS ONLY)

Run power cable to installation location. For ducting through top of hood, existing plate remains in place on inside back of hood.

For ducting through back of hood, remove existing plate from inside back of hood and remove the rough-in plate from the top of hood. Attach the plate to inside top of hood to cover hole. Secure to threaded studs with same (4) nuts. Install the rough-in plate to the back of hood so that the wiring box is located on the right side as you are facing the hood.

Connect ducting to rough-in plate as you are installing the rough-in plate. Use duct tape to make all joints secure and air-tight.

ROUGH-IN PLATE

ON TOP OF HOOD

WIRING

LOCKNUTS

COVER

LOCKNUTS

HD0262 PLATE ON BACK OF HOOD

15. CONNECT THE WIRING (ALL BLOWERS)

!WARNING

Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power to be switched on accidentally.

Remove wiring cover from rough-in plate or electrical compartment and set aside.

INTERNAL BLOWERS: Connect cable into wiring box using wire connectors. Connect BLACK to BLACK, WHITE to WHITE and GREEN or bare wire under GREEN ground screw.

CAUTION

The ORANGE wire (A) is for make-up air device connection only. If there is no make-up air device, never remove the cap on the ORANGE wire end.

Reinstall wiring cover.

IN-LINE OR EXTERIOR BLOWERS: See instructions included with blower.

A

HE0088

- 11 -

Page 10 Page 12
Image 11
Page 10 Page 12
Contents E60000 Series Installation InstructionsTo Reduce the Risk of a Range TOP Grease Fire E60000 Series Range Hood System Internal Blowers Model HLB3 280 CFM NON-DUCTED Installation Select Blower Option and Installation TypePrepare the Installation Measure InstallationInstall Backsplash Optional Prepare the Installation CONT’DRemove the Adapter Internal Blower Hoods only Remove Filters and the Grease Drip RailChoose the Openings Internal Blowers Hood only Horizontal Discharge Installation Internal Blowers Hood only Ducted Installation only Install the Adapter and the Transition if Need beInstall Wood Mounting Strip Install AEE Optional Soffit ChimneyROUGH-IN Plate Location External Blowers Hoods only Install the HoodConnect the Wiring ALL Blowers Install the Blower Exterior or IN-LINE Blower Reinstall Grease Drip Rail and Baffle FiltersInstall Light Bulbs Operation USE and CareOperation CONT’D WarrantyInternal blowers hoods Wiring DiagramsService Parts

E60000 Series specifications

The Broan E60000 Series is a top-of-the-line ventilation solution designed for modern kitchens, seamlessly combining style with functionality. This series aims to enhance indoor air quality while complementing a wide variety of kitchen designs. With several models based on preferences for size, power, and additional features, the E60000 series stands out for its innovative technologies and user-friendly characteristics.

One of the main features of the Broan E60000 Series is its powerful ventilation capabilities. With a range of CFM (Cubic Feet per Minute) options, homeowners can select the perfect power level to suit their cooking habits. Whether preparing a simple meal or a gourmet feast, the series efficiently removes smoke, steam, and odors, ensuring a comfortable cooking environment.

Another notable characteristic is the series' sleek and stylish design. With a selection of finishes including stainless steel, black, and white, these range hoods can fit seamlessly into any kitchen aesthetic. The hood's minimalist look, combined with its low-profile design, maximizes headroom while adding a touch of elegance to any kitchen space.

The E60000 Series also incorporates advanced technology for an enhanced user experience. The models feature multiple fan speeds, allowing users to adjust the ventilation power based on their cooking needs. Additionally, the series is equipped with bright, energy-efficient LED lighting, providing excellent visibility on the cooking surface. This not only enhances functionality but also adds a modern touch to the aesthetic appeal of the kitchen.

Ease of installation and maintenance is another significant advantage of the Broan E60000 Series. The hoods come with easy-to-follow instructions, making installation straightforward for both DIY enthusiasts and professionals. The removable grease filters are dishwasher-safe, ensuring that maintaining the hood's performance is a hassle-free process.

In summary, the Broan E60000 Series combines powerful performance, elegant design, and advanced technologies to create an ideal ventilation solution for kitchen environments. Whether you are renovating your kitchen or building a new one, this series provides the quality and efficiency needed to elevate your cooking experience, all while enhancing the overall ambiance of your home.
Top Page Image Contents