Preparing Range Hood, Preparando EL Extractor

PREPARING THE

RANGE HOOD

1.Unpack hood and check contents. You should receive:

1- Aluminum Filter

1- 3-1/4" x 10" Damper/Duct Connector (mounted inside of hood for shipping only) (Save screws for mounting.)

1- 7” Round Duct Plate (mounted on top of hood) (not shown) (Save screws for mounting.)

2.Remove 7” round duct plate from top of hood. Set duct plate aside - with mounting screws.

3.Remove wiring box cover. Under cover find:

1- Plastic Bag containing loose mounting hardware

4.For non-ducted installation, remove louver cover from front of hood. (FIG. 3)

5.Remove either top or rear electrical knockout de- pending upon whether wiring will enter hood from wall or cabinet. (FIG. 4)

DUCTED INSTALLATION ONLY

NOTE

Louver cover must be installed as shown in

Figure 3 to function in ducted mode.

6.Remove appropriate duct knockout on hood by inserting screwdriver into edge of knockout and breaking tabs holding knockout to hood. You may have to tap screwdriver with hammer to break tabs. Peel knockout back with pliers. (FIG. 5)

NOTE TAKE CARE WHEN REMOVING THE 3¼”

X 10" VERTICAL DUCT KNOCKOUT. DO NOT DAMAGE THE 7" ROUND DUCT KNOCKOUT.

7.Fit damper/duct connector over opening and secure in place with black sheet metal screws. (FIG. 6)

Hinge pins and damper/duct connector should be toward top of hood for ducting through wall or to- ward back of hood for ducting through cabinet above hood. Seal joint between damper/duct con- nector and hood with duct tape.

8.7” round ducted discharge only: Re-install 7” round duct plate removed in Step #2 under “PRE- PARING THE RANGE HOOD” section. For best performance, line up the 7” round duct plate with the 7” round opening on hood. Mount duct plate to hood with 2 screws from duct plate and 2 screws from 3¼” x 10” damper. Install a 7” round damper (purchase separately). Damper flap must open freely in direction of air flow (away from range hood).

OMIT STEP 9 if range hood will be installed under cabinets with flush bottom.

9.(For installation on recessed bottom cabinets only) Attach a wood filler strip at each side of recessed area under cabinet. (Use two 1" x 2" strips cut to length.) If recess is more than 1" use thicker strips. Attach strips with 1-1/4" screws about 3" from each end. See FIG. 7.

10.Measure and mark the following (FIGS. 7 & 8):

a)Electrical line opening

b)Duct opening

11.Drill four pilot holes in corners of marked duct opening as shown and cut opening with saber saw or keyhole saw.

12.Use 1-1/4" drill bit to drill opening for electrical connection in wall or cabinet.

13.Hold hood up against cabinet bottom and trace keyhole slots onto cabinet bottom of filler strips.

14.Screw the four supplied 7/8" wood screws for mounting the hood into the exact center of the narrow end of the keyhole slots marked under- neath the cabinet. Allow 3/8" of the screws to project, so the hood can be fitted into place.

FIG. 2

KEYHOLE SLOTS

RANURAS EN FORMA

DE HUECO DE

CERRADURA

							WIRING BOX COVER
							TAPA DE LA CAJA DE
ALUMINUM FILTER							CABLEADO
FILTRO DE ALUMINIO
FILTRO DE ALUMINIO

DAMPER/DUCT CONNECTOR

CONECTOR AL REGULADOR/DUCTO

FIG. 3

FIG. 4

FIG. 5

FIG. 6

FIG. 7

CUT STRIPS TO FIT

CORTE LAS TIRAS PARA

QUE QUEPAN

DUCT OPENINGS

ABERTURA PARA		CENTER LINE
ABERTURA PARA		LINEA CENTRICA
EL DUCTO		LINEA CENTRICA
EL DUCTO

	WIDTH OF
	RANGE HOOD
	ANCHO DEL		ELECTRICAL WIRING OPENING
	EXTRACTOR		ABERTURA PARA EL
			CABLEADO ELECTRICO

PREPARANDO EL

EXTRACTOR

1.Desempaque el extractor y revise el contenido de la caja. Usted debe de encontrar:

1 -Filtro de aluminio

1 -Conector de ducto/regulador de 3-1/4" x 10" (montado dentro del extractor para embarque solamente) (Guarde los tornillos para el montaje.)

1-Placa del conducto redondo de 7” (montado en del ex- tractor) (no se muestra) (Guarde los tornillos para el montaje.)

2.Quite la placa del conducto redondo de 7” de la parte superior de la campana. Colóquela aparte, con los tornil- los de montaje.

3.Quite la cubierta de la caja de cableado. Bajo la tapa encontrará:

1 -Una bolsa de plástico que contiene herrajes sueltos para instalación

4.Para instalaciones sin ducto, quite la tapa de la rejillas de la parte frontal del extractor. (FIG. 3)

5.Quite la tapa de quitar golpeando eléctrica de arriba o atrás dependiendo en donde entra el cableado al extrac- tor de la pared o del gabinete. (FIG. 4)

INSTALACION CON DUCTO SOLAMENTE

NOTA

La cubierta de las rejillas se debe instalar como se muestra en la figura 3 para que funcione con el conducto.

6.Quite la placa de quitar golpeando en el extractor insertando un destornillador en el filo y rompiendo las conexiones que lo sostienen al extractor. Es posible que tenga que golpear el destornillador con un martillo para romper estas uniones. Pele la tapa de quitar golpeando hacia atrás con una tenaza. (FIG. 5)

NOTA

TENGA CUIDADO AL QUITAR EL AGUJERO CIEGO DEL CONDUCTO VERTICAL DE 8.25 X 25.4 CM (3¼” X 10"). NO DAÑE EL AGUJERO CIEGO DEL CONDUCTO REDONDO DE 17.78 CM (7").

7.Junte el conector del regulador/ducto sobre la abertura y sujételo en su sitio con tornillos negros de metal para lámina. (FIG. 6)

Los pasadores de bisagra y el conector del regulador/ ducto deben de estar hacia la parte de arriba del ex- tractor para pasar el ducto a través de la pared o hacia la parte de atrás del extractor para pasar el ducto a través de gabinete encima del extractor. Selle la unión entre el conector regulador/ducto con cinta de ducto.

8.Sólo para descargas con conducto redondo de 7”: Vuelva la instalar la placa del conducto redondo de 7” que quitó en el paso 2 de la sección “PREPARANDO EL EXTRACTOR.” Para obtener un mejor rendimento, alinee la placa del conducto redondo de 17.8 cm (7”) con la abertura redonda de 17.8 cm (7”) de la campana. Monte la placa del conducto al la campana con does tornillos desde la placa del conducto y con dos tornillos desde el tiro de 8.3 x 25.4 cm (3¼” x 10”). Instale un regulador de tiro redondo de 7” (se compra por separado). La aleta del regulador se debe abrir libermente en dirección del flujo de aire (en sentido contrario a la campana la estufa).

OMITA PASO 9 si el extractor estará instalado debajo de un gabinete con la parte inferior plana.

9.(Para instalación en gabinetes ahuecados solamente) Sujete una tira de madera a cada lado de la parte infe- rior ahuecada debajo del gabinete. (Use dos tiras de madera de 1" x 2" cortadas al largo necesario.) Si el ahuecamiento es más de 1" use tiras más gruesas. Sujete las tiras con tornillos de 1-1/4" a una distancia de más o menos 3" del extremo. Véase FIG. 7.

10.Mida y marque lo siguiente (FIG. 7 & 8):

a)Abertura para la línea eléctrica

b)Abertura para el ducto

11.Perfore cuatro huecos pilotos en las esquinas ya marcadas de la abertura para el ducto como se muestra y luego corte un abertura con un serrucho sable o un serrucho para cerradura.

12.Usese una broca de 1-1/4" para perforar una abertura para la conexión eléctrica en la pared o gabinete.

13.Sostenga al extractor debajo de la parte inferior del gabinete y trace las ranuras en forma de hueco de cerradura en la parte inferior del gabinete donde se instalarán las tiras de madera.

14.Atornille cuatro de los tornillos de madera de 7/8" para montar el extractor en el centro exacto de la parte estrecha de la ranuras en forma de cerradura que se marcaron debajo del gabinete. Permita que 3/8" de los tornillos queden afuera, para que luego pueda instalarse al extractor en su sitio.

46000 specifications

The Broan 46000 series is a highly regarded line of range hoods that blends performance with sleek design, making it a popular choice for modern kitchens. Designed to provide efficient ventilation and elevate the culinary experience, this series boasts an impressive range of features and technologies that enhance both functionality and aesthetics.

One of the standout features of the Broan 46000 series is its powerful ventilation capabilities. With options ranging from 250 to 400 CFM, these range hoods effectively eliminate smoke, heat, and odors, resulting in a fresher cooking environment. The advanced ventilator design ensures improved air circulation, ensuring that your kitchen remains comfortable, even during extensive cooking sessions.

In terms of operation, the Broan 46000 offers easy-to-use controls for hassle-free functionality. Most models are equipped with user-friendly push-button controls that allow you to select from multiple fan speeds and lighting options. The intuitive design ensures that you can adjust the settings quickly, even while you’re busy cooking.

Lighting is another vital aspect of the Broan 46000 series. Many models come equipped with bright, energy-efficient LED lights that illuminate your cooking surface. This provides not only better visibility for cooking tasks but also enhances the overall ambiance of your kitchen. The integrated lighting fixtures are designed to be both practical and aesthetically pleasing, further enhancing the range hood's sleek appearance.

The construction of the Broan 46000 also deserves mention. Made from durable stainless steel, these range hoods are designed to withstand the rigors of daily kitchen use while resisting corrosion and ensuring long-lasting performance. The smooth surfaces make for easy cleaning, which is a significant advantage for busy households.

Another notable characteristic of the Broan 46000 series is its versatile installation options. The hoods in this series can be installed as either under-cabinet or wall-mounted units, offering flexibility to fit various kitchen designs. This adaptability makes it easy to incorporate the range hood into any kitchen layout, enhancing both the functionality and style of the space.

In summary, the Broan 46000 series range hoods provide exceptional performance, user-friendly features, and an elegant design, making them a smart choice for any modern kitchen. With powerful ventilation, energy-efficient lighting, and durable construction, these range hoods are engineered to meet the needs of aspiring home chefs and everyday cooks alike. Whether you are renovating your kitchen or simply seeking an upgrade, the Broan 46000 series is an excellent addition that will elevate your cooking expereince.