Capresso 156 warranty Changing Parameters, Changing the Grinder Fineness, Program Dial fig

Page 14

10. Changing Parameters

Besides the six different coffee options and the cup sizes you can change a variety of parameters as explained in chapters 10.1 through 10.6.

10.1 Changing the Grinder Fineness

Important: You can only adjust the fineness during the actual grinding process. For darker beans, we recommend grinding somewhat coarser (turn the selector to the thicker bars, clockwise); for lighter beans, we recommend grinding somewhat finer (turn to finer bars, counterclockwise), see fig. 10.

Please note: If coffee drips very slowly through the coffee spout, the coffee was ground too fine. Adjust to a coarser grind. If coffee flows too fast through the coffee spout, adjust to a finer grind.

10.2 The Program Dial (fig. 12)

The Program Dial is located behind the door on the left side (fig. 1, 1b). It has a small black button in the middle. We call it the "P Button". During normal oper- ation the Program Dial points to position 1. On the inside of the door you will find a card explaining the different positions. The program dial is used to:

change parameters (position 2, 3, 7, 8)

perform maintenance functions (position 4, 5, 6); see chapters 12.1 to 12.4.

check statistics (position 9); see chapter 12.6.

10.3 Changing the Coffee Temperature

a. Turn the Program Dial to Pos. 2. The display shows TEMPERATURE/HIGH. Push the P Button once. The display will change to TEMPERATURE/REGULAR. Push it again and it will go back to high and so on.

b. In HIGH the temperature of the coffee is approximately 7º F higher than in setting REGULAR.

Please note:

The temperature of the coffee is also influenced by the grinder setting and the amount of coffee you are using. A finer grind will slightly increase the temperature of the coffee.

For highest temperature pre-warm the cups.

10.4 Auto Shut-Off Settings

Turn the Program Dial to Pos. 3. The display shows AUTO SHUT-OFF / AFTER 2 HOURS. Push the P Button repeatedly and the display will show 3, 4, 5, - ,1, 2, and so on. In position "–" the machine will not turn off automatically. All other selections will turn off the machine after last use, automatically.

10.5 Changing the Language

Turn the Program Dial to Pos. 8. The display shows LANGUAGE / ENGLISH. Pushing the P Button you can choose from the following options:

LANGUE / FRANCAIS

French

TAAL / NEDERLANDS

Dutch

SPRACHE / DEUTSCH

German

LINGUA / ITALIANA

Italian

IDIOMA / ESPANOL

Spanish

And then back to English.

 

14

Image 14
Contents Fully Automatic Coffee and Espresso Center Important Safeguards Very Important Ground Coffee Residue10a 10bSteam/Water Dial SW Dial Steam Position b Hot Water Position cLift & Pull Preparation Different Coffee Drinks Welcome To The Capresso C1300Crema Coffee and Pressure Brewing Coffee Facts Please Dont... or you void your warranty protectionFactory Settings Please DoFilling the Bean Container Using Oily BeansFilling the Water Tank First Time PreparationDaily Preparation Grinding and Brewing CoffeeFrothing and Steaming Using Pre-ground CoffeeUsing Hot Water Steaming PositionCleaning the Frother Heating and Frothing MilkAutomatic Monitoring Controls Empty TrayChanging Parameters Changing the Coffee TemperatureAuto Shut-Off Settings Changing the Grinder FinenessChanging the Water Hardness Claris Water CartridgeReplacing the Claris Cartridge Installing and Activating the Claris Water Filter CartridgeGeneral Cleaning Instructions FilterCleaning / Press P Button Cleaning with Special TabletHow to clean with the special tablet Extra Rinse CycleHow to Decalcify Decalcifying Special Liquid Durgol requiredClearing for Transport Counter / HOT Water Counter / Steam Counter / Filter TroubleshootingUser Statistics Supplies Display shows Replace Filter but I just replaced the filterThis warranty does not cover