Bertazzoni PM6V B Descriptions, Using burners, Descriptive Caption for HOB Description of Hobs

Page 6

3)Beside the tap bar on the work top, use a small screwdriver that fits the screw (gold) found on the lower part of the tap and turn the fixing screw to the right or left until the flame of the burner is regulated in the most suitable way to MINIMUM.

4)Make sure that that the flame does not go out when changing the position quickly from MAXIMUM to the MINIMUM position.

ATTENTION: The regulation described above can be carried out only with burners using natural gas, while with burners using propane gas the screw must be fully screwed in, in a clockwise direction.

Descriptions

DESCRIPTIVE CAPTION FOR HOB

DESCRIPTION OF HOBS

1.

Dual burner

Model ‘A’ Fig. 11

2.

Rapid burner

Model ‘B’ Fig. 12

3.Medium burner

4.Small Burner

5.Dual in burner control knob

6.Dual out burner control knob

7.Rapid burner control knob

8.Medium burner control knob

9.Small burner control knob

Service & maintenance instructions

Service and maintenance only to be carried out by an authorised person

To replace parts such as burners, valves and electric components, the hotplate must be removed from the bench top by releasing the attachment hooks, loosening the attachment screws of each burner, unscrewing the hotplate attachments nuts which are visible at the bottom of the surface, removing the hotplate top and finally replacing the defective parts.

Note: if the valves must be replaced, first disassemble the ignitions switches wires.

It is recommended to replace the valve gaskets each time the valve is replaced, thus ensuring a perfect seal between the body and the gas train.

WARNING: Disconnect power before servicing unit.

For the location of the wall receptable for the connection of the three-pin earthed plug of the appliance, see indications given in Fig. 1- 2

WARNING: After first installation of the appliance or after any service intervention concerning main gas parts of the appliance, make the leak test using water with soap on the gas connections in order to verify the correct installation. Do not use fire for gas leak testing.

User instructions

WARNINGS:

Keeping appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquid.

Do not store dangerous or flammable material in the cabinet areas above appliance; store them in a safe place in order to avoid potential hazards.

For safe use of appliance, do not use it for space heating.

Do not use aerosol sprays in the vicinity of this appliance while it is in operation For description of hotplates refer to installation instructions.

Using burners

A diagram is etched on the control panel above each knob which indicates which burner corresponds to that knob.

Manual ignition:

Manual ignition is always possible even when the power is cut off or in the event of prolonged power failure. Turn the knob that corresponds to the burner selected counterclockwise to the MAXIMUM position at the etched star (large flame) and place a lit match up to the burner.

Burners fitted with a safety device (thermocouple):

6

Image 6
Contents Dimensions 605 mmW x 520 mmD Requirements Information for the InstallerInserting the hotplate Overhead clearances Minimum valuesAttaching the hotplate Min. ClearancesVentilation of the Premises Position and Ventilation Connecting the Appliance to the GAS SupplyWiring diagrams Wiring diagram description Connection of the Appliance to the Electricity SupplyRegulation of burners Maintenance of the Machine Changing the PartsRoom ventilation Location and venting Regulation of the Minimum on the burnersDescriptions Using burnersBurners fitted with a safety device thermocouple Descriptive Caption for HOB Description of HobsTable B Burner Cleaning the applianceTips for using burners correctly Correct usage of pansExigences Distances des meubles suspendus Valeurs minimum Installation, Service et Instructions pour l’UtilisateurInsertion de la table de cuisson Distances latérales Valeurs minimumVentilation DE LA Piece Emplacement ET AerationFixation de la table de cuisson Raccordement DE LA Table AU Reseau DU GAZSchémas de câblage Branchement Electrique DE LA TableChangement DES Composants Ventilation du local Positionnement et dégazage Réglage des brûleursRéglage du Minimum sur les brûleurs Description DES Tables Tables DE CuissonAllumage électrique automatique Utilisation des brûleursAllumage manuel Brûleurs équipés d’un dispositif de sécurité thermocoupleNettoyage de l’appareil AFig.5B Bertazzoni S.p.a. Via Palazzina 8, 42016 Guastalla, Italia